Bedienungsanleitung Vonroc MS504AC (Seite 17 von 104) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch, Polnisch)

778562

Zoom out

Zoom in

Vorherige Seite

1/104

Nächste Seite

WWW.VONROC.COM

2. Move the adjustable fence to the inner position,

towards the blade. The maximum distance

between the adjustable fence (35) and the saw

blade (6) is 8mm, as shown on ﬁgure J. Make

sure the fence does not touch the blade.

3. Firmly clamp the workpiece;

4. Turn on the machine. Make sure that the saw

blade has reached full speed;

5. Now bring the handle slowly downwards so that

the saw blade cuts through the piece of work

and passes through the slot in the table. Do not

put undue pressure on the saw, let the machine

do the work;

6. Bring the handle gently up again and switch it

off by letting go of the switch.

Making a bevel cut (ﬁg. L, M)

Follow these steps to make an angled cut to the

edge of the wood:

1. Adjust the mitre angle to 0° and the bevel angle

to the desired position ;

2. Move the adjustable fence to the outer position,

away from the blade. The maximum distance

between the adjustable fence (35) and the saw

blade (6) is 8mm, as shown on ﬁgure M. Make

sure the fence does not touch the blade.

3. Firmly clamp the workpiece. Ensure the work-

piece clamp is placed on the right side;

4. Turn on the machine. Make sure that the saw

blade has reached full speed;

5. Now bring the handle slowly downwards so that

the saw blade cuts through the piece of work

and passes through the slot in the table. Do not

put undue pressure on the saw, let the machine

do the work;

6. Bring the handle gently up again and switch it

off by letting go of the switch.

Making a compound cut (ﬁg. M, N)

Follow these steps to make a combination of mitre

and bevel cut:

1. Adjust the mitre angle and the bevel angle to

the desired position ;

2. Move the adjustable fence to the outer position,

away from the blade. The maximum distance

between the adjustable fence (35) and the saw

blade (6) is 8mm, as shown on ﬁgure M. Make

sure the fence does not touch the blade.

3. Firmly clamp the workpiece. Ensure the work-

piece clamp is placed on the right side;

4. Turn on the machine. Make sure that the saw

blade has reached full speed;

5. Now bring the handle slowly downwards so that

the saw blade cuts through the piece of work

and passes through the slot in the table. Do not

put undue pressure on the saw, let the machine

do the work;

6. Bring the handle gently up again and switch it

off by letting go of the switch.

Using the slide function

For extra wide workpieces, the machine is equipped

with a sliding function. When using the slide function,

make sure to loosen the locking bolt for slide rails

(29). Pull the handle (2) away from the fence (9) until

the saw blade is in front of the workpiece. Slowly

guide the tool arm downwards using the handle and

afterwards push the handle (2) towards the fence (9)

and saw through the workpiece with uniform feed.

For small workpieces, it is possible to ﬁx the sliding

function in the rear position of the saw with the

locking bolt for slide rails (29). If more cutting

width is desired, then it is necessary to loosen the

locking bolt for slide rails (29).

Using the length stop (Fig. O)

The length stop (8) on both the left and right table

extensions (10) can be used for easily sawing

workpieces to the same length.

1. Move the length stop (8) upwards;

2. Loosen the locking bolt for table extension (34);

3. Adjust the table extension (10) to the required

length.

4. Tighten the locking bolt for table extension (34).

Adjusting the depth stop (Fig. P)

The depth stop can be adjusted, to limit the cutting

depth. This can be used to easily saw a groove. To

do so:

1. Loosen the knurled nut for depth adjustment

(45);

2. Adjust the knob for depth adjustment (24) to

the desired depth;

Tighten the knurled nut for depth adjustment (45).

Switching the laser on/off (Fig. B)

Press the laser switch (46) to switch the laser on

or off. The laser switch (46) also turns on the LED

worklight.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Vonroc MS504AC Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info