Bedienungsanleitung Vonroc MS504AC (Seite 18 von 104) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch, Polnisch)

778562

Zoom out

Zoom in

Vorherige Seite

1/104

Nächste Seite

WWW.VONROC.COM

Fine-tuning

Prior to any adjustment work disconnect

the mains power plug.

To ensure precise cuts, the basic settings of the

saw must be checked and adjusted before ﬁrst use,

as well as necessary after intensive use. Suitable

special tools are required for this. Vonroc after-sales

will help handling this work quickly and reliably.

Fine-tuning the laser (Fig. Q)

Note: To test the laser function, the power tool

must be connected to the power supply.

While adjusting the laser (e.g. when moving

the tool arm), never activate the on/off

switch. Accidental starting of the power tool

can lead to injuries.

If the laser (18) ceases to indicate the correct cut-

ting line, you can readjust the laser. To do so:

1. Loosen the laser adjustment screws (48) and

set the laser by moving it until the laser beam

strikes the teeth of the saw blade (6);

2. Tighten the laser adjustment screws (48).

Fine-tuning the 0° bevel angle (Fig. R, S)

1. Adjust the mitre and bevel angle to 0°;

2. Lower the handle (2) and secure it using the

position lock knob (38);

3. Lock the slide movement using the locking bolt

for slide rails (29);

4. Set an angle gauge to 90° and place it on the

table (11), as shown on ﬁgure S. The leg of the

angle gauge must be ﬂush with the saw blade

(6) along its entire length;

5. Loosen the lock nut for 0° bevel angle (50);

6. Adjust the stop bolt for 0° bevel angle (32) until

the leg of the angle gauge is ﬂush with the saw

blade along its entire length;

7. Re-tighten the lock nut for 0° bevel angle (50).

Subsequently check the position of the angle indica-

tor (19). If necessary loosen the pointer using a Phi-

lips screwdriver, set to position 0° on the scale for

bevel angle (20) and re-tighten the retaining screw.

Fine-tuning the 45° bevel angle (Fig. R, T)

1. Adjust the mitre and bevel angle to 45°;

2. Lower the handle (2) and secure it using the

position lock knob (38);

3. Lock the slide movement using the locking bolt

for slide rails (29);

4. Set an angle gauge to 90° and place it on the

table (11), as shown on ﬁgure T. The leg of the

angle gauge must be ﬂush with the saw blade

(6) along its entire length;

5. Loosen the lock nut for 45° bevel angle (49);

6. Adjust the stop bolt for 45° bevel angle (31)

until the leg of the angle gauge is ﬂush with the

saw blade along its entire length;

7. Re-tighten the lock nut for 45° bevel angle (49).

Subsequently check the position of the angle indica-

tor (19). If necessary loosen the pointer using a Phi-

lips screwdriver, set to position 45° on the scale for

bevel angle (20) and re-tighten the retaining screw.

Fine-tuning the 0° mitre angle (Fig. U, V)

1. Set an angle gauge to 0° on the table (11) and po-

sition it between the fence (9) and the saw blade

(6);

2. The leg of the angle gauge must be ﬂush with the

saw blade (6) along its entire length;

3. Loosen the locking bolts for adjustable fence

(35) and subsequently loosen the safety bolts for

adjustable fence (36).

4. Remove both left and right adjustable fences (7),

revealing the fence bolts (51).

5. Loosen all four fence bolts (51) and adjust the

fence (9) until the leg of the angle gauge is ﬂush

with the saw blade along its entire length;

6. Retighten all four fence bolts (51) again. Subse-

quently check the position of the angle indicator

(17). If necessary loosen the pointer using a

Philips screwdriver, set to position 0° on the scale

for mitre angle (16) and re-tighten the retaining

screw.

7. Mount both left and right adjustable fences (7).

Tighten the locking bolts for adjustable fence

(35) and subsequently tighten the safety bolts

for adjustable fence (36).

5. MAINTENANCE

Always make sure that the machine is not

connected to the mains electricity when you

carry out any maintenance of the mechanism.

Clean the machine casings regularly with a soft

cloth, preferably after each use. Make sure that the

ventilation openings are free of dust and dirt. Re-

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Vonroc MS504AC Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info