Bedienungsanleitung Vonroc PH501AC - Albano (Seite 5 von 56) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Spanisch, Polnisch, Schwedisch)

764173

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

WWW.VONROC.COM

sons not capable of leaving the room on their own,

unless constant supervision is provided. The device

is to be used only for its prescribed purpose. Any

other use is deemed to be a case of misuse.

TECHNICAL SPECIFICATIONS

Model No. PH501AC

Voltage 220-240 V~

Frequency 50-60 Hz

Power 1500W

Heating element type Carbon ﬁbre lamp

Heating time 3 seconds

Wave length 3.0-1000 microns

Radiant efﬁciency

90%

Heating distance

2-3m

Heating area

7-9m

Colour temperature 1600 K

Overheat protection Yes

Electronic soft start Yes

Ingress protection class IP44

Protection class Class I

Weight 2.36 kg

DESCRIPTION

The numbers in the text refer to the diagrams on

page 2.

1. Hanging chain

2. Power cable

3. Hanging hook

4. Carbine hook

5. On/off switch

6. Heater

7. Protective grill

8. Remote control

9. Remote control switch

10. Receiver for remote control

3. ASSEMBLY

This heater should be installed by a

competent person, i.e. a qualiﬁed electrician.

Always disconnected the heater from the

electrical supply and allow it to cool before

installation.

Installing the heater (Fig. A, C)

Always mount the device with the supplied

accessories.

Before starting the installation, take the following

into consideration:

• Place the device on a ﬁrm, level ceiling surface;

installation of the heater should be on a strong

rigid support (such as strong wooden beams or

metal rails etc).

• The device must be hung so that there is 50

cm of free space between the heater and any

ceiling, tent canvas etc. There must also be

at least 1.80 m between the ground and the

underside of the device. Refer to Fig. C. The

device can never be hung on a hook in the wall

as it could hang at a slant!

• The Hook used to hang the heater must be able

to take a weight 3 or 4 times that of the heater

itself.

• Ensure that the power supply cable is well

mounted and that it does not come into contact

with reﬂector of the heater or that does not trail

into heated area.

• Do not install the heater on an inﬂammable

surface.

• If the heater is to be used outside, a weatherp-

roof outlet is highly recommended.

• Before drilling ensure that there are no wires or

water pipes in the area where the heater is to

be installed.

To install the heater, follow these steps:

• The device is supplied with a hanging chain (1)

and two carbine hooks (4). Put a carbine hook

(4) on both ends of the chain (1).

• Mount one side of the chain onto the hanging

hook (3) using the carbine hook (4), as shown

on ﬁg. A.

• Provide an attachment point from which the

device can hang down freely and that is sturdy

enough to hold the heater without any pro-

blems. Fix it ﬁrmly in such a way that it cannot

drop, slip, slide or otherwise move.

• Attach the unused carbine hook (4) on the

heater chain onto the provided ceiling hook or

ceiling hanging eye.

• Take into account the minimum distances as

shown on ﬁgure C.

• Plug the patio heater into a grounded power

outlet. Check beforehand if the voltage rating

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Vonroc PH501AC - Albano Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info