Bedienungsanleitung Vonroc PH502AC - Marsili (Seite 8 von 64) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Spanisch, Polnisch, Schwedisch)

764175

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

8WWW.VONROC.COM

control the room temperature so do not use this

heater in spaces when they are occupied by per-

sons not capable of leaving the room on their own,

unless constant supervision is provided. The device

is to be used only for its prescribed purpose. Any

other use is deemed to be a case of misuse.

TECHNICAL SPECIFICATIONS

Model No. PH502AC-PH503AC

Voltage 220–240 V ~

Frequency 50-60 Hz

Power 2000W

Power settings 1: 1000W

2: 2000W

Heating element type Low glare lamp

Heating time 1 second

Wave length 0.78-1.4 microns

Radiant efﬁciency 90%

Heating distance 4-5m

Heating area 10-12m

Colour temperature 1500K

Overheat protection Yes

Electronic soft start Yes

Ingress protection class IP55

Protection class Class I

Weight 2.03 kg

DESCRIPTION

The numbers in the text refer to the diagrams on

page 2-5.

1. Heater

2. Protective grill

3. Receiver for remote control

4. Power cable

5. On/off switch

6. Mode button

7. Remote control on/off switch

8. Power level 1 button

9. Power level 2 button

10. Mounting bracket

11. Sleeve anchor

12. Screw with washers

13. Nut

14. Bolt

3. ASSEMBLY

This heater should be installed by a

competent person, i.e. a qualiﬁed electrician.

Always disconnected the heater from the

electrical supply and allow it to cool before

installation.

Installing the heater (Fig. A-N)

Always mount the device with the supplied

accessories.

Before starting the installation, take the following

into consideration:

• Place the device on a ﬁrm, level surface.

• The device must be mounted so that there is

50 cm of free space between the heater and

any ceiling, tent canvas etc. There must also

be at least 1.80 m between the ground and the

underside of the device. Refer to Fig. J and K.

The device may never be hung at an angle!

• Ensure that the power supply cable is well

mounted and that it does not come into contact

with reﬂector of the heater or that does not trail

into heated area.

• Do not install the heater on an inﬂammable

surface.

• If the heater is to be used outside, a weather-

proof outlet is highly recommended.

• Before drilling ensure that there are no wires or

water pipes in the area where the heater is to

be installed.

To install the heater on a wall or ceiling, follow

these steps:

1. The device is supplied with the mounting acces-

sories as shown in ﬁgure C.

2. Drill a total of 4 holes using the dimensions in

ﬁgure D. The hole diameter should be the same

diameter as the anchor diameter: 8mm. Drill at

least 10 to 15 mm deeper than the expected

embedment. Ensure the holes are level and at

exactly the same height.

3. Clean out the holes of any debris.

4. Set the nut ﬂush with the top of the sleeve

anchor (11), shown as step 1 in ﬁgure E.

5. Insert the sleeve anchor (11) into the hole in

the base material, shown as step 2 in ﬁgure E.

Using a hammer, insert the sleeve anchor as far

until the washer and nut are tight against the

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Vonroc PH502AC - Marsili Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info