Bedienungsanleitung Vonroc S-RS501DC (Seite 9 von 36) (Deutsch, Englisch, Holländisch, Französisch)

764103

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

WWW.VONROC.COM

1. Insert the battery (4) into the base of the machi-

ne as shown in Fig. F.

2. Push the battery further forward until it clicks

into place.

Removing the battery from the machine (Fig. A, F)

1. Push the battery unlock button (5)

2. Pull the battery out of the machine like shown

in Fig. F.

Checking the battery charging status (Fig. G)

• To check the battery charge status, push the

button (13) on battery shortly.

•

The battery has 3 lights indicating the charge

level, the more lights that burn, the more charge

the battery has left.

•

When the lights are not burning it means the bat-

tery is empty and must be charged immediately.

Charging the battery with the charger (Fig. G)

1. Take the battery (4) from the machine.

2. Turn the battery (4) to upside down position and

slide it onto the charger (15) as shown in Fig. G.

3. Push the battery until it is fully pushed into the

slot.

Plug the charger plug into an electrical outlet

and wait for a while. The LED indicators on the

charger (16) will lighten up and show the charger

status.

The charger has 2 LED indicators (16) which indica-

the status of the charging process:

Red LED Status Green LED status Charger status

Off Off No power

Off On

Standby mode:

- No battery is

inserted or,

- Battery inserted

but charging has

ﬁnished

On Off Battery charging in

progress

• Fully charging the 2Ah battery may take up to

60 minutes.

• Fully charging the 4Ah battery may take up to

120 minutes.

After the battery is fully charged remove the char-

ger plug from the outlet and remove the battery

from the charger.

When the machine is not being used over a

longer period of time it is best to store the

battery in charged condition.

Replacing the saw blade (Fig. A, C)

When mounting the saw blade, wear

protective gloves. Danger of injury when

touching the saw blade.

Only use saw blades that correspond with

the characteristic data given in the

operating instructions.

Mounting the saw blade

Make sure the blade holder is free of material

debris (such as splinters of wood or metal).

1. Turn the clamping lever (9) as far to the left as

possible and hold it in this position.

2. Insert the saw blade in the chuck (8). Check

that the saw blade is securely ﬁxed and that the

teeth are pointing downwards.

3. Let go of the clamping lever. Check whether the

saw blade is locked in place.

Make sure to use the right sawblade for the corres-

ponding material. Included with the machine is a

coarse sawblade for wood and a ﬁne sawblade for

metal and plastics.

Removing the saw blade

1. Turn the clamping lever (9) as far to the left as

possible and hold it in this position.

2. Remove the saw blade from the chuck (8).

3. Let go of the clamping lever.

4. OPERATION

Switching the machine on/off (Fig. A)

The on/off switch (2) is used for activating the

machine and adjusting speed.

• To start the machine, press and hold the lock-

off button (1) and press the on/off switch (2).

• The further the on/off switch (2) is being

pushed, the faster the blade will move. The

required speed depends on the material and

can be determined by practical testing.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Vonroc S-RS501DC Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info