Bedienungsanleitung Vonroc S-RS501DC (Seite 10 von 36) (Deutsch, Englisch, Holländisch, Französisch)

764103

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

WWW.VONROC.COM

•

To stop the machine, release the on/off switch (2).

Adjusting the base plate (Fig. B)

Due to its movability, the baseplate (7) angle

adapts to the workpiece. Furthermore, the length

of the baseplate can be adjusted depending on the

required sawing depth.

1. Loosen the baseplate bolts (11) using the hex

key (10) provided.

2. Adjust the baseplate (7).

3. Tighten the baseplate bolts (11) using the hex

key (10) provided. It is possible to store the hex

key onto the machine, as shown on Fig. B.

Plunge cutting (Fig. D)

Plunge cutting may only be used on soft materials

such as wood, aerated concrete, gypsum plaster

boards, etc. However, this requires a certain practi-

se and is only possible with short saw blades.

Place the saw onto the workpiece and switch it on.

2. Ensure that the bottom edge of the footplate

rests on the workpiece surface as shown.

3. Slowly saw into the workpiece at an angle, mo-

ving the saw to a vertical position and continue

to saw along the cutting line.

4. Switch the saw off and lift off the workpiece

when the work is complete.

Flush cutting (Fig. E)

Elastic bi-metal saw blades allow you to saw

protruding objects (e,g, water pipes, iron bars, etc,)

nearby the wall.

1. Apply the saw blade directly to the wall and

bend slightly so that the footplate rests against

the wall. Pay attention that the saw blade

always extends beyond the diameter of the

material being worked.

Switch the machine on and saw off the workpiece

keeping constant lateral pressure against the wall.

Optimum use

• Adjust saw blade and stroke rate to suit the ma-

terial to be processed. For right radius curves it

is best to use a narrow saw blade. Apply coolant

or lubricant to deal with the ﬂuttering produced

along the cut line when sawing metal.

• Check wood, chip boards, building materials

etc, for hard materials (nails, screws etc.), befo-

re sawing and remove them, if necessary.

•

Clamp material well. Do not support the workpie-

ce with hand or foot. Do not touch objects or the

ﬂoor with the saw running (danger of backlash).

• Put the footplate on the surface of the workpie-

ce, and saw through it with constant contact

pressure or feed. If the saw blade seizes switch

the machine off immediately. Spread the gap

with a suitable tool and pull out the saw blade.

• After ﬁnishing work, switch off the machine and

only put down after it has come to a complete

standstill.

5. MAINTENANCE

Before cleaning and maintenance, always

switch off the machine and remove the

battery pack from the machine.

Clean the machine casings regularly with a soft

cloth, preferably after each use. Make sure that the

ventilation openings are free of dust and dirt. Re-

move very persistent dirt using a soft cloth moiste-

ned with soapsuds. Do not use any solvents such

as gasoline, alcohol, ammonia, etc. Chemicals such

as these will damage the synthetic components.

ENVIRONMENT

Faulty and/or discarded electrical or

electronic apparatus have to be collected at

the appropriate recycling locations.

Only for EC countries

Do not dispose of power tools into domestic waste.

According to the European Guideline 2012/19/EC

for Waste Electrical and Electronic Equipment and its

implementation into national right, power tools that

are no longer usable must be collected separately

and disposed of in an environmentally friendly way.

WARRANTY

VONROC products are developed to the highest

quality standards and are guaranteed free of defects

in both materials and workmanship for the period

lawfully stipulated starting from the date of original

purchase. Should the product develop any failure

during this period due to defective material and/or

workmanship then contact VONROC directly.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Vonroc S-RS501DC Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info