Bedienungsanleitung Vonroc S-WC501AC (Seite 8 von 52) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch, Türkisch)

764060

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

WWW.VONROC.COM

Cutting disc

Diameter:

Bore:

150mm

22.2mm

Spindle thread M12

Protection class IP20

Weight 5.1kg

Sound pressure L

85.3 dB(A)

Acoustic power L

96.3 dB(A)

Uncertainty (K) 3 dB(A)

Vibration (main grip) 7.214 m/s

Vibration (auxiliary grip) 5.843 m/s

Uncertainty (K)

1.5

m/s

Wear hearing protection.

Vibration level

The vibration emission level stated in this instruc-

tion manual has been measured in accordance

with a standardized test given in EN60745; it may

be used to compare one tool with another and as

a preliminary assessment of exposure to vibration

when using the tool for the applications mentioned.

• Using the tool for different applications, or with

different or poorly maintained accessories, may

signiﬁcantly increase the exposure level.

• The times when the tool is switched off or when

it is running but not actually doing the job, may

signiﬁcantly reduce the exposure level.

Protect yourself against the effects of vibration by

maintaining the tool and its accessories, keeping

your hands warm, and organizing your work patterns.

DESCRIPTION

The numbers in the text refer to the diagrams on

pages 2 - 4.

1. On/off switch

2. Lock-off button

3. Locking knob for slot depth

4. Scale for slot depth

5. Spindle lock button

6. Guard

7. Base

8. Guide roller

9. Dust extraction connection

10. Main grip

11. Auxiliary grip

12. Allen screws

13. Allen key

14. Spindle

15. Outer ﬂange

16. Flange key

17. Cutting disc

18. Spacers

19. Cutting disc

20. Spindle sleeve

21. Inner ﬂange

22. Dust extraction adapter

3. ASSEMBLY

Before assembly, always switch off the

machine and remove the mains plug from

the mains.

Replacing the cutting discs (ﬁg. B - D)

Worn or damaged cutting discs must be replaced

immediately.

- Only use sharp and undamaged cutting

discs.

- Only use cutting discs that are suitable

for the material to be worked.

- Only use cutting discs with a maximum

permitted speed that is equal to or

exceeds the maximum no-load speed

of the machine.

- Only use diamond cutting discs that are

suitable for dry cutting.

- Always replace both cutting discs at the

same time.

- Never attempt to remove the guard.

• Place the machine on a stable surface.

• Loosen the Allen screws (12) using the Allen

key (13).

• Loosen the locking knob (3) and lower the base

(7).

• Remove the guard (6).

• Keep the spindle lock button (5) pressed to lock

the spindle (14).

• Loosen the outer ﬂange (15) using the ﬂange

key (16). To untighten, turn clockwise. To tighten,

turn anti-clockwise.

• Remove the old cutting disc (17), the spacers

(18), the old cutting disc (19), the spindle

sleeve (20), and the inner ﬂange (21).

• If necessary, clean the ﬂanges (15 & 21).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Vonroc S-WC501AC Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info