Bedienungsanleitung Vonroc S3-SG502DC (Seite 10 von 104) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Spanisch, Polnisch, Schwedisch)

764115

Zoom out

Zoom in

Vorherige Seite

1/104

Nächste Seite

WWW.VONROC.COM

Checking the battery charging status (Fig. C-2)

• To check the battery charge status, push the

button (28) on battery shortly.

• The battery has 3 lights indicating the charge

level, the more lights that burn, the more charge

the battery has left.

• When the lights are not burning it means the bat-

tery is empty and must be charged immediately.

Charging the battery with the charger (Fig. C-2)

1. Take the battery (4) from the machine.

2. Turn the battery (4) to upside down position and

slide it onto the charger (30) as shown in Fig.

C-2.

3. Push the battery until it is fully pushed into the

slot.

4. Plug the charger plug into an electrical outlet

and wait for a while. The LED indicators on the

charger (31) will lighten up and show the char-

ger status.

The charger has 2 LED indicators (29) which indi-

cate the status of the charging process:

Red LED Status Green LED status Charger status

Off Off No power

Off On

Standby mode:

- No battery is

inserted or,

- Battery inserted

but charging has

ﬁnished

On Off Battery charging in

progress

• Fully charging the 2Ah battery may take up to

60 minutes.

• Fully charging the 4Ah battery may take up to

120 minutes. After the battery is fully charged

remove the charger plug from the outlet and

remove the battery from the charger.

When the machine is not being used over a

longer period of time it is best to store the

battery in charged condition.

Connecting the motor unit to the spray unit

(Fig. D)

• With one hand hold the motor unit (8) straight

up and with the other hand place the spray unit

(7) on a 90˚ angle onto the motor unit (8). Like

show in ﬁgure D.

• Align the spray unit (7) slot with the notch insi-

de the motor unit (8). Rotate the spray unit (7)

90 degrees down until you hear a click.

Disconnecing the motor unit and spray unit (Fig. E.)

• Hold the motor unit (8) and press the discon-

nect latch (6) in the direction to the spray unit

(7) and turn 90˚ degrees to take off the spray

unit (7).

Connecting and disconnecting the container to the

spray unit.

• To connect: Align the container (11) with the

container cap(10) and tighten.

• To disconnect: Loosen the container (11) from

the container cap (10)

Replacing the nozzle and nozzle needle

The nozzle will be assembled on the spray gun

when taken out of the box. To replace the nozzle

follow the following steps.

• Loosen the nozzle nut (17) and remove it.

• Take out the nozzle head (15) and Nozzle (14)

from the machine.

• Loosen the nozzle needle (13) by using the

needle key (18) like show in ﬁgure I.

• Take the new nozzle needle (24 or 26) and

place it back in the spray unit and tighten by

using the nozzle key (18)

• Take the new nozzle (25 or 27) and attach it to

the nozzle head (15)

• Place the nozzle head (15) and nozzle assembly

back in the spray unit

• Close it by tightening the Nozzle nut (17).

4. OPERATION

Preparing the spray gun for use

Step 1: Viscosity/diluting of the paint

This appliance can process spray materials up to

max. 70 DIN/sec (viscosity). Low-viscosity coating

substances, water- and solvent based paints, ﬁn-

ishes, primers, 2 component paint, clear ﬁnishes,

staining sealers and wood sealer preservatives

often do not need diluting. High-viscosity Wall

paints, thick varnishes and thick stains often do

need diluting.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Vonroc S3-SG502DC Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info