Bedienungsanleitung Vonroc S3-SG502DC (Seite 11 von 104) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Spanisch, Polnisch, Schwedisch)

764115

Zoom out

Zoom in

Vorherige Seite

1/104

Nächste Seite

WWW.VONROC.COM

Tip! With low-viscocity use the smaller nozzle and

with high-viscocity use the bigger nozzle.

Warning! Always use wall paint that is

smooth and without any granules or lumps.

Otherwise the nozzle will become clogged.

PAINT PREPARATION

Check/test the viscosity of the to be sprayed material.

• Put the stirring rod (12) in the container(11)

which includes the to be sprayed material and

pull it out and see how the material drips. When

it looks like liquid chocolate, this material is

ok for testing at step 4 (Test and adjusted the

spray jet effect, spray volume and spray ﬂow).

When the spraying material is very thick and

gel-like, dilute it by 5 or 10%.

For small batches this can easily done by using the

special stirring rod:

1. Put the stirring rod (12) in the container like

shown in ﬁgure E1 and add spray material up to

one of the lines. Like shown in ﬁgure E2.

2. For 10%: Add the suitable thinning solvent up to

the next line.

For 5%: Add the suitable thinning solvent up to

half of the next line.

3. Stir the thinning solvent through the spray

material until it is completely mixed.

Check viscosity again, when it looks like liquid

chocolate, this material is ok for testing at step

4 (Test and adjusted the spray jet effect, spray

volume and spray ﬂow). Still to thick? Repeat the

process by adding an additional 5 or 10% thinning

solvent.

Tip! Most wall paints are thick and may need up to

40% dilution.

Step 2: Preparing the spray surface

• Cover the area around the to be sprayed area

thoroughly and over a wide area. Any surface

that is not covered properly can unintentionally

be sprayed.

Warning! Be aware of your surroundings

when spraying outside, wind can cause

unintentional spraying of your not covered

surroundings

• The spray surface needs to be clean, dry, and

free from grease or dust.

• Polished surfaces should be lightly sanded, and

the sanding dust removed.

Step 3: Filling the paint container

• Remove the container (11) from the Spray unit.

• Fill the container with to be sprayed material to a

maximum of 800ml.

• Adjust the riser pipe (23) according to the

position you are going to use the spray gun in.

Spraying angle up like show in Fig. F. spraying

angle down like show in Fig. G

• Make sure the gasket and riser pipe (23) are

properly installed in the container cap (10). Tight-

en the container (11) onto the container cap (10).

Step 4: Test and adjust the spray jet effect, spray

volume and spray ﬂow. (Fig. A + B)

Note: Before starting to spray the work surface, it

is advisable to make an initial test by spraying a

small area on scrap material.

Tip! With low-viscocity use the smaller nozzle and

with high-viscocity use the bigger nozzle.

Choose the jet effect: Horizontally

•

or vertical-



•

. By turning the nozzle adjusting ring (16)

left or right.

2. Adjust the spray volume with Spray volume adjust-

ing wheel (9) by turning it to the left - to reduce

the volume, to the right + to increase. Note: Low

volume is advised for smaller object or surfaces.

High volume is advised or bigger surfaces.

Tip: We recommend starting at the minimum setting.

3. Adjust the spray ﬂow by using the spray ﬂow

adjustment knob(2): turn the knob to the left

to reduce the ﬂow, to the right to increase the

ﬂow. Note: The thinner the paint the lower the

ﬂow should be, when using thicker paint make

sure to use a higher ﬂow.

Tip: Several light layers rather than one thick layer

will help prevent the paint running.

4. Aim the spray gun to the to be sprayed surface

and pull the trigger (1). Hold the front of the spray

gun around 20-30 cm away from the to be sprayed

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Vonroc S3-SG502DC Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info