Bedienungsanleitung Vonroc S_OT501DC (Seite 8 von 56) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch, Türkisch)

778554

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

WWW.VONROC.COM

Vibration level

The vibration emission level stated in this instruc-

tion manual has been measured in accordance

with a standardised test given in EN 62841; it may

be used to compare one tool with another and as

a preliminary assessment of exposure to vibration

when using the tool for the applications mentioned:

- using the tool for different applications, or with

different or poorly maintainted accessories,

may signiﬁcantly increase the exposure level

- the times when the tool is switched off or when

it is running but not actually doing the job, may

signiﬁcantly reduce the exposure level.

Protect yourself against the effects of vibration by

maintaining the tool and its accessories, keeping

your hands warm, and organizing your work patterns.

DESCRIPTION

The numbers in the text refer to the diagrams on

page 2-3.

1. On/off switch

2. Speed adjustment wheel

3. Mounting point for accessories

4. Grip

5. Quick change lever

6. Work light

7. Battery

8. Battery unlock button

9. Battery LED indicators button

10. Battery LED indicators

11. Charger

12. Charger LED indicators

3. ASSEMBLY

Before any work on the power tool, remove

the battery.

The battery must be charged before ﬁrst use.

Inserting the battery into the machine (Fig. C)

Ensure that the exterior of the battery is

clean and dry before connecting to the

charger or machine.

Insert the battery (7) into the base of the machine

as shown in Fig. C.

2. Push the battery further forward until it clicks

into place.

Removing the battery from the machine (Fig. C)

1. Push the battery unlock button (8).

2. Pull the battery out of the machine like shown

in Fig. C.

Checking the battery charging status (Fig. D)

• To check the battery charge status, push the

button (9) on battery shortly.

•

The battery has 3 lights indicating the charge

level, the more lights that burn, the more charge

the battery has left.

•

When the lights are not burning it means the bat-

tery is empty and must be charged immediately.

Charging the battery with the charger (Fig.D)

1. Take the battery (7) from the machine.

2. Turn the battery (7) to upside down position and

slide it onto the charger (11) as shown in Fig. D.

3. Push the battery until it is fully pushed into the

slot.

Plug the charger plug into an electrical outlet

and wait for a while. The LED indicators on the

charger (12) will lighten up and show the charger

status.

The charger has 2 LED indicators (12) which indica-

the status of the charging process:

Red LED Status Green LED status Charger status

Off Off No power

Off On

Standby mode:

- No battery is

inserted or,

- Battery inserted

but charging has

ﬁnished

On Off Battery charging in

progress

• Fully charging the 2Ah battery may take up to

60 minutes.

• Fully charging the 4Ah battery may take up to

120 minutes.

After the battery is fully charged remove the char-

ger plug from the outlet and remove the battery

from the charger.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Vonroc S_OT501DC Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info