Bedienungsanleitung Vonroc S_PM501AC (Seite 6 von 40) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

778354

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

WWW.VONROC.COM

bonnet or its attachment strings to spin freely.

Tuck away or trim any loose attachment strings.

Loose and spinning attachment strings can

entangle your ﬁngers or snag on the workpiece.

Do not press the spindle lock until the tool stops.

Kickback and Related Warnings

Kickback is a sudden reaction to a pinched or

snagged rotating wheel, backing pad, brush or

any other accessory. Pinching or snagging causes

rapid stalling of the rotating accessory which in

turn causes the uncontrolled power tool to be

forced in the direction opposite of the accessory’s

rotation at the point of the binding. For example,

if an abrasive wheel is snagged or pinched by the

workpiece, the edge of the wheel that is entering

into the pinch point can dig into the surface of the

material causing the wheel to climb out or kick out.

The wheel may either jump toward or away from

the operator, depending on direction of the wheel’s

movement at the point of pinching. Abrasive wheels

may also break under these conditions. Kickback

is the result of power tool misuse and/or incorrect

operating procedures or conditions and can be avoi-

ded by taking proper precautions as given below.

a) Maintain a ﬁrm grip on the power tool and

position your body and arm to allow you to

resist kickback forces. Always use auxiliary

handle, if provided, for maximum control over

kickback or torque reaction during start-up.

The operator can control torque reactions or

kickback forces, if proper precautions are taken.

b) Never place your hand near the rotating acces-

sory. Accessory may kickback over your hand.

c) Do not position your body in the area where

power tool will move if kickback occurs.

Kickback will propel the tool in direction opposite

to the wheel’s movement at the point of snagging.

d) Use special care when working corners, sharp

edges etc. Avoid bouncing and snagging the

accessory. Corners, sharp edges or bouncing

have a tendency to snag the rotating accessory

and cause loss of control or kickback.

e) Do not attach a saw chain woodcarving blade or

toothed saw blade. Such blades create frequent

kickback and loss of control.

Electrical safety

Always check that the voltage of the power

supply corresponds to the voltage on the

rating plate.

• Do not use the machine if the mains cable or

the mains plug is damaged.

•

Only use extension cables that are suitable for

the power rating of the machine with a minimum

thickness of 1.5 mm

. If you use an extension

cable reel, always fully unroll the cable.

2. MACHINE INFORMATION

Intended use

This machine is intended for polishing and brushing

metal and coated surfaces.

TECHNICAL SPECIFICATIONS

Model No. S_PM501AC

Voltage 220-240 V~

Frequency 50Hz

Power 1050W

No-load speed 1400-4800/min

Disc diameter 150 mm

Weight 2.7 kg

Sound pressure level L

87dB(A), K=3dB(A)

Sound power level L

98dB(A), K=3dB(A)

Vibration

12.59 m/s

Vibration level

The vibration emission level stated in this instruc-

tion manual has been measured in accordance

with a standardized test given in EN60745; it may

be used to compare one tool with another and as

a preliminary assessment of exposure to vibration

when using the tool for the applications mentioned.

• Using the tool for different applications, or with

different or poorly maintained accessories, may

signiﬁcantly increase the exposure level.

• The times when the tool is switched off or when

it is running but not actually doing the job, may

signiﬁcantly reduce the exposure level.

Protect yourself against the effects of vibration by

maintaining the tool and its accessories, keeping

your hands warm, and organizing your work patterns.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Vonroc S_PM501AC Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info