Bedienungsanleitung Waeco MagicSpeed MS50 (Seite 43 von 122) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

517983

Zoom out

Zoom in

Vorherige Seite

1/122

Nächste Seite

7.0 INSTALLING THE VACUUM SERVO UNIT (SEE

✎✎

✎ C 1)

The vacuum servo unit (B 2) regulates the throttle-setting and controls the

speed of the vehicle. The kit contains a vacuum servo unit with a flexible

throttle lever. The best places for installation in the engine compartment

are the bulkheads and the inside wheel arches. In order to avoid damage

to the electronics and mechanics, make sure that temperatures does not

exceeded 100°C. ✎ C 2 to E 3 illustrate various methods for attaching the

wire to the carburettor. ✎ D 2 gives a detailed list of the components for

the vacuum servo unit. The following points describes how the wire is to

be attached to the carburettor. To ensure perfect functioning of the cruise

control, the throttle control-lever must be in good condition (e.g. not slack,

not seized, etc.). If your vehicle has fuel injection, the installation

instructions refer to the throttle control-lever and not to the carburettor,

and in the case of diesel engines to the fuel injection pump.

1. Decide which method is possible for attaching the throttle lever to the

throttle linkage (see ✎ C 2 and C 3). At vehicles without throttle lever

the attachment can be made directly at the accelerator (see ✎ E 2)

Note: The servo has about 40 mm of travelling distance. Choose a

stopping point at the accelerator or cable of the vehicle, which

corresponds as nearly as possible to the distance of 40 mm. Non-

compliance with this would result in excessive strain of the servo or a

restricted working range. The wire must pull on the throttle control

lever in a straight line. The sideways pull must not be more than 20°.

2. Using two 6 x 19 mm metal screws , attach the vacuum servo-unit to

the inside wheel arch or the bulkhead of the vehicle.

3. Depending on the method for attaching the actuator cable the

illustrated components will be used (see ✎ D 1 and D 2)

CAUTION! The throttle lever must be kept away from rotating

or hot surface parts.

202

5.0 NØDVENDIG VERKTØY (SE

✎✎

✎ A 5 TIL A 17)

Følgende verktøy er nødvendig for installasjon og montering:

- Målestokk (se ✎ A 5)

- Kjørner (se ✎ A 6)

- Hammer (se ✎ A 7)

- Metallborsett (se ✎ A 8)

- Boremaskin eller drill (se ✎ A 9)

- Vanlige skrutrekkere og stjernetrekkere i forskjellige størrelser

(se ✎ A 10)

- Flatfil og halvrundfil

- Blyant eller filtpenn

- Fastnøkkelsett (se ✎ A 11)

- Skrallenøkkelsett (se ✎ A 12)

- Jekk og bilbukker (se ✎ A 13)

Til elektrisk tilkobling og testing trenger du:

- diodetestlampe (se ✎ A 1) eller voltmeter (se ✎ A 2)

- krympetang (se ✎ A 15)

- evt. isoleringsbånd

- kabelbånd

- varmekrympeslange

- Varmluftsføner

- loddebolt (se ✎ A 16)

- loddetinn (se ✎ A 17)

Book_MS-50_A6.p65 10-02-2003, 11:1143

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Waeco MagicSpeed MS50 Seite 43

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info