Bedienungsanleitung Wamsler W1-90 (Seite 44 von 104) (Deutsch, Englisch, Französisch, Italienisch)

813266

Zoom out

Zoom in

Vorherige Seite

1/104

Nächste Seite

cleaned free from soot. By removing the hob and heating plates the flue gas channel and

the flue pipe inside the stove can also be cleaned. By loosening the screw of the cleaning

cover (4) the lower part of the flue gas channel around the oven can also be cleaned.

After finishing cleaning, the heating and hob plates must be replaced correctly. The clean-

ing cover (4) under the oven needs to be closed tightly again.

PLEASE NOTE:

After every period of heating you should check the stove thoroughly. If repairs or

replacements are necessary, please contact your supplier with the necessary article

numbers and serial number in good time.

3.7.2 Varnished and enamel surfaces

Only wipe down the external surfaces when the stove is cold. Varnished surfaces should

only be washed with plain water (do not scrub). Enamel surfaces in special cases can be

cleaned with soapsuds or a bit of washing-up liquid and then wiped dry.

NOTE: Never use sponges, scouring products or any other chemical or abrasive

cleaning products!

3.7.3 Ceramic glass surfaces

Clean the window and/or Ceran plate before first use with a clean damp cloth. Then rub a

few drops of a ceramic glass protection product onto the glass / Ceran plate with a paper

towel.

After wiping this and polishing it dry, the high quality surface is now covered with an invisi-

ble film. The helps to keep the glass pane /Ceran plate clean and if repeated regularly,

makes it easy to clean.

3.7.4 Sheet steel

The steel sheet parts must be rubbed over with an acid-free sheet steel care product when

at blood temperature. Cleaning is then done when the stove is cold.

The special steel plates which radiate heat need to be taken care of regularly after each

time you cook. After any use which causes dampness or dirt to collect on the plate, you

must clean it. The hob plate should be cleaned when it is still lukewarm, which allows any

remaining water to evaporate and so prevents rust forming. Take care that you do not use

water to clean the stove when it is cold.

Expansion joints in the steel hob plate must always be cleaned free of adhesions, to avoid

deforming the steel hob plate and the side panels. If necessary the edge of the cover

should also be cleaned of any adhesions.

3.7.5 Changing the light bulb

The light bulb in the oven is exposed to high temperatures. Although it is a special kind of

bulb, it can still burn out in time. You just need to replace it with the same type of bulb

(15 W - 240 V - 300°C).

Before changing it make sure that the stove is not in use, that it is cold and that the bulb

has not been switched on. Unplug the electrical cable and check that there is no current

present. To change the bulb, remove the protective cover, change the bulb and replace the

bulb protector.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Wamsler W1-90 Seite 44

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info