Bedienungsanleitung Wanders Cocos (Seite 19 von 68) (Deutsch, Englisch, Holländisch, Französisch)

533285

Zoom out

Zoom in

Vorherige Seite

1/68

Nächste Seite

Switching from ºC/24-hour to ºF/12-hour indication

t Press the OFF button e and the small ame button d simultaneously (2 sec) to switch from ºF (and the

12-hour indication) to the ºC (and the 24-hour indication), and vice versa.

Possible settings

t By pressing the SET button f you can switch quickly between MAN Â day temperature Â night tem-

perature Â timer Â MAN.

t MAN: this setting allows you to turn the ames manually higher or lower with the big-ame button c or

the small-ame button d.

t Day temperature (): this mode allows you to set the desired daytime temperature; the remote control

set will function as a thermostat.

t Night temperature (e): this mode allows you to set the desired night temperature.

t TIMER: this mode allows you to preset 2 switch-on and 2 switch-o times per 24 hours. If the night setting

is on - - -, the stove will burn on the pilot ame.

Setting the temperature

t Select the day temperature or night temperature by briey pressing SET button f.

t Now press SET button f longer until the display starts ashing.

t Preset the temperature with buttons c or d (5 ºC is the minimum day temperature).

t Wait or press OFF button e to switch back to the thermostat-controlled system.

t In order to save the batteries you are advised to reset the night-temperature until the display shows the

‘- - -‘ signal.

Setting the timer function

t Select the timer function by briey pressing SET button f a few times.

t Now press the SET button f longer until P1 () starts ashing.

t Set the hours with button c and the minutes with button d.

t Briey press SET button f for the next timing.

t Once all 4 timings have been set, press OFF button e to end the presetting.

Operation (remote control)

Igniting the re

t Open the gas turncock that is xed in the gas pipe leading to the stove.

t Press “O I” switch g on the gas control block in the “I” position.

t Turn control button h on the gas control block to the ON position.

t Simultaneously press buttons e and c on the handset. A short acous-

tic signal indicates the start, and is followed by short acoustic signals

(0.2 sec/signal, 1Hz.) until the pilot ame and the chief burner are ig-

nited. After the main burner has lit, the ame height will automatically

go to the maximum position.

Possible error messages

t Long signals (0.8 sec. signal with 0.2 sec. interval) during lighting Â: batteries of the receiver are almost

empty. (After hearing this signal, you can switch on the appliance for about another 10 times.)

t 5 seconds continuous signal Â: error message. One of the cables may not be connected, or the “O I” switch

is not in the “I” position.

t 5 short signals (0.2 sec. signal with 0.2 sec. interval) Â: ignition of the pilot ame and the main burner has

failed. Possible cause: air in the pilot burner pipe.

Important: If the pilot ame has gone out you must wait at least 5 MINUTES before repeating the

above-mentioned steps.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Wanders Cocos Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Wanders Cocos

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info