Bedienungsanleitung Wanders Cocos (Seite 20 von 68) (Deutsch, Englisch, Holländisch, Französisch)

533285

Zoom out

Zoom in

Vorherige Seite

1/68

Nächste Seite

Setting the height of the ames

t After igniting the burner, the height of the ames will automatically reach the maximum position.

t Press button d continuously to lower the ames and to switch o the burner (putting the re out: “STAND

BY”). Press button d briey to gradually lower the ames.

t Press button c to increase the ame height. Briey press button c to gradually increase the ames.

Switching o the appliance

t Press button d to lower the ames and to switch o the burner.

t Then press “OFF” button e to switch o the entire unit, including the pilot ame.

t If the appliance is not used for a longer period it is advisable that you turn o the gas valve in the gas pipe.

Important: if the pilot ame has gone out for whatever reason, you must wait at least 5 MINUTES

before lighting the pilot ame again.

Failure

If it looks as if the signals of the remote control are not properly received by the stove (receiver), it may be

caused by:

t Empty batteries: change the batteries.

t An electronic problem: solve it by pressing the “RESET” button on the receiver.

t If the appliance often switches o you should contact your installer.

Control (manual control)

If the batteries are due for replacement or if the receiver is defect, you can also operate the hearth by hand.

To do so, you need to disconnect the ignition (piezo) cable of the receiver and slide it gently onto the piezo

connection of the gas control block.

Lighting the re and putting it out

1. Open the gas stopcock which is mounted in the gas pipe leading to

the appliance.

2. Press “O I” switch g on the gas control block in the “I” position.

3. Turn motor switch i on the gas control block all the way to the right.

The switch will make a ticking sound.

4. Turn operating switch h on the gas control block in the MAN

position; an orice j becomes visible.

5. Push the metal pin in the orice with something like a small pen. The

gas will now ow to the pilot.

6. While keeping the metal pin pressed in, press the (square) ignition

fuse k (next to the “O I” switch) to ignite the pilot ame. Look through

the glass to see whether the pilot ame is burning.

7. If the pilot ame is burning, keep the metal pin pressed for another

10 seconds and then release it. If the pilot ame dies, wait for another

5 minutes before repeating the above steps.

8. Turn operation knob h to the “ON” position.

9. Turn motor switch i to the left to ignite the burner and to select the

height of the ames.

10. Turn motor switch i all the way to the right to put out the re; the pilot ame will keep burning.

11. If you want to put out the pilot ame as well, turn “O I” switch g to the “O” position.

12. Close the gas tap.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Wanders Cocos Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Wanders Cocos

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info