Bedienungsanleitung Wanders Square 60G (Seite 21 von 68) (Deutsch, Englisch, Holländisch, Französisch)

533293

Zoom out

Zoom in

Vorherige Seite

1/68

Nächste Seite

Control (manual control)

If the batteries are due for replacement or if the receiver is defect, you can also operate the hearth by hand.

To do so, you need to disconnect the ignition (piezo) cable of the receiver and slide it gently onto the piezo

connection of the gas control block.

Lighting the re and putting it out

1. Open the gas stopcock which is mounted in the gas pipe leading to

the appliance.

2. Press “O I” switch g on the gas control block in the “I” position.

3. Turn motor switch i on the gas control block all the way to the right.

The switch will make a ticking sound.

4. Turn operating switch h on the gas control block in the MAN

position; an orice j becomes visible.

5. Push the metal pin in the orice with something like a small pen. The

gas will now ow to the pilot.

6. While keeping the metal pin pressed in, press the (square) ignition

fuse k (next to the “O I” switch) to ignite the pilot ame. Look through

the glass to see whether the pilot ame is burning.

7. If the pilot ame is burning, keep the metal pin pressed for another

10 seconds and then release it. If the pilot ame dies, wait for another

5 seconds before repeating the above steps.

8. Turn operation knob h to the “ON” position.

9. Turn motor switch i to the left to ignite the burner and to select the

height of the ames.

10. Turn motor switch i all the way to the right to put out the re; the pilot ame will keep burning.

11. If you want to put out the pilot ame as well, turn “O I” switch g to the “O” position.

12. Close the gas tap.

Using the hearth for the rst time

When you light your gas hearth for the rst time, the hearth must ‘anneal’. The unit has a heat-resistant lacquer

which must still burn in. Though this may give an unpleasant smell, it is otherwise harmless. It is advisable to

burn the stove at its highest position for about three hours while airing the room well.

Discolouration of walls, ceilings and grates

After lighting your hearth, the walls, ceilings and grates may show some discolouration. This is caused

by the dust particles that burn in the convection cover. This is a natural process for which WANDERS

cannot be held responsible. To minimize discolouring we refer to the advice given for atmospheric

hearths. Your installer can give you more information about this.

Some deposit may form on the ceramic glass of the door of the hearth. You can easily remove this deposit with

a damp cloth when the glass is cold. If necessary you can use a special cleansing agent for ceramic rings. Page

26 shows you how to remove the glass.

Watch out for nger marks!

Make sure to leave no nger marks on the cleaned glass pane when you close the hearth door. Finger

marks leave stains which will burn in the glass.

When you ignite the hearth for the rst time, the hearth calculates how much time is needed to reach the

preset temperature. On this basis, the hearth selects the most ecient way to heat the room.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Wanders Square 60G Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Wanders Square 60G

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info