Bedienungsanleitung Watts Climatic Control Heating and Cooling (Seite 11 von 28) (Englisch)

805499

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

5.4.6

Wireless RF outside sensor (Inst:  System parameters: Input, “OUSE”).

As an option you can plug in a wireless RF outside sensor room thermostat to the ClimaticControl-HC. This solu-

tion is very interesting in rehabilitation, to avoid wires trough the wall, in a building management with several CC-

HC, in this case only one outside sensor can be installed to manage all the building.

WIRELESS OUTSIDE

SENSOR

The wireless outside sensor can be used only with the 433,92Mhz frequency

RF outside sensor initialization to the Controller:

 SYSTEM PARAMETERS MENU, section

(Inst:  System parameters: “OUSE”)

fig.9

RF supervising function.

If the ClimaticControl-HC is installed with RF thermostat(s) and there is no radio signal received during more than 2

hours, a display alarm will be activated,the backlight and the small RF antenna logo radio will blink.

To stop the alarm, maintain the (OK) button pressed for about 10 seconds.

Check the batteries of the RF thermostat(s) or outside RF sensor. Please replace them if exhaust-

ed.

Check the position in which the antenna was installed. It must be installed in vertical position.

Installation in or on a metal body can abate the power of radio transmission. Minimize the distance

to the RF thermostat.

If radio alarm is displayed:

Due to the wireless thermostat, the regulation will continue to work as an installation without thermostat (no com-

pensation).

Due to the Wireless outside sensor, the regulation will continue to work with the last value received from the out-

side sensor.

5.4.7

Inputs functions (In1 & In2)

If no wired thermostat is installed in the house, you will have the possibility to use the two available inputs of your

ClimaticControl-HC for different functions (Inst:  System parameters: Input, “In1 & In2”).

Input1

Inst:  System parameters: Input, “HC”

You could use the input 1 to connect the an external signal which give the Heating or Coling working mode

of the installation (This signal could be done directly by a reversible input).

Inst:  System parameters: Input, “Aqu”

1/ You could use the input 1 to connect the an imersion thermostat witch schould be placed in a storage

tank. In Heating mode this immersion thermostat will be use to switch off the circulation pump (Pump1) to

avoid cold water circulation in the circuit if the storage tank is discharged. (This solution is generally use

when solid wood burner is installed)

2/ You could also use this input to have a priority on domestic hot water.

In this case the pump of the heating circuit will be stopped to keep the priority on the domestic hot water. This

configuration is not compatible with the Efficiency Point PE=Yes as the output is used to control the heating stage

2 (See parameter #15 in Chap 7.1 System parameters setting)

Note:

The heating output will stay activated even if the aquastat have stopped the circulation pump.

To avoid problem in cooling mode, if the storage tank is filled with cold water (by heat pump...) the

aquastat function will be automatically desactivated.

Radio

alarm:

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Watts Climatic Control Heating and Cooling Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info