Bedienungsanleitung Watts WFHC Master H C-Bus slave (Seite 9 von 56) (Deutsch, Englisch, Holländisch, Französisch, Italienisch)

805490

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

Type of the

Heating &

Cooling

commutation

(There is a 2

minutes standby

without control to

avoid hot / cold

overlap)

rF: The Heating & Cooling mode will be done by the Master HC thermostat WFHT-

BASICH&C-BUS.

* Generally use when separate system is installed. (Boiler, water chillers...)

CtAC: The Heating & Cooling mode will be done by the Heat Pump connected on

the special input of your RF receiver (see the wiring for more explanation)

* Generally use when manual or automatic reversible Heat pump

SEnS: The heating & Cooling mode will be done by the WFH-SENSOR installed on

the incoming pipe of the manifolds and connected on the special input on RF

receiver (see the wiring for more explanation) * Generally use when reversible heat

pump without Heat & Cool information and control is installed.

for humidity input, then you need to connect a NTC or humidity sensor (refer to

chapter 10.A)

for External control, use this input (free contact) to switch OFF the installation; per

example you can connect a GSM module. (refer to chapter 10.B)

The following parameters are only available if a water humidity sensor (NTC 10K or free contact sensor) is

connected and installed on the incoming pipe of the manifolds

(See the schematic and system drawing to install the sensor)

Setting level to switch off the cooling function to avoid

residual humidity in the house:

When the water temperature in the pipe decrease

under this level during the time of the anti short cycle

adjusted on “F9” the cooling function will be stopped.

Press (OK) to view the instantaneous value measured

by the sensor.

Default: 18°C

Adjustable: 5 to 25°C

Minimum time to decide to stop the cooling function

when the water temperature decreases under the “F8”

level.

Default: 30

Adjustable: 00 to 60min

Type of degrees displayed

°C: Celsius degrees.

°F: Fahrenheit degrees.

Type of time displayed

Default: 24H00

Adjustable: 12:00 am/pm

Selection of the proportional band (PWM) duration in

minutes

You could decrease this time up to 15min only if your

installation as fast thermal reacting behavior

(Liquid concrete floor, ...)

Default: 20 minutes

Adjustable: 0 to 120 min

Value of the proportional band (PWM)

Adjust this value like this:

A well insulated house « 1.5°C »

A not insulated house « 4°C »

Default: 3.0°C

Adjustable: 0.1 to 6°C

Press (OK) during 5 seconds to reset the installation.

All parameters are replaced by default value.

Master Heat&Cool thermostat Bus configuration mode (see the corresponding section)

Standard thermostat Bus configuration mode (see the corresponding section)

Press (OK) on this parameter to exit the parameters menu end come back to the main display.

8. Thermostat alarm

- You could see the alarm on the Master (Red blinking LED on the concerned zone and alarm sound).

To stop immediately the alarm sound, press the (OK) key.

- If an alarm is detected on one zone, the regulation will be maintained on this zone by average of the actual room

temperatures of the other zones used on the Master.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Watts WFHC Master H C-Bus slave Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info