Bedienungsanleitung Watts WFHC Master H C-Bus slave (Seite 10 von 56) (Deutsch, Englisch, Holländisch, Französisch, Italienisch)

805490

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

9. Thermostat initialization

1/ Standard thermostat initialisation: WFHT-BASIC-BUS or WFHT-LCD-BUS

First of all to enter in the parameters menu, go to the Comfort mode, press once and maintain the (Ok) key then press

on the same time on the (◄) key. The first parameter must be appears “F0 ProG”, you can now release the keys.

By pressing several times on the (►) key, go to the “rF init” parameters, then press again on the (OK) key to enter in the

“rf init” mode. The following display (Fig.a) must appear:

Fig.a Fig.b Fig.c

Graphic scope description:

2 squares (Fig.b) = reception of correct init signal from a thermostat.

1 square (Fig.c) = reception of standard signal from a thermostat.

nothing = the receiver did not detect any Bus signal. (Check the connection)

1. Use (◄) & (►) to change the zone number and move the green blinking LED cursor on the master/slave DISPLAY.

Use (Ok) to select or de-select this zone and move to the next zone. (The zones selected stay light up in green)

Use (+) & (-) to choose the sense of the reduced temperature in cooling mode in accordance with the following

description:

Add => The reduced temperature (+2°C) will be added to the comfort temperature during the night period when

the system works in cooling mode.(Example: for living room, during the night you don’t need to cool this zone)

Sub => The reduced temperature (-2°C) will be subtracted to the comfort temperature during the night period

when the system works in cooling mode.(Example: for bed room, during the night you need to cool this zone)

no => no cooling on this zone.(Example: no cooling for bathroom, kitchen or room with residual humidity)

2. When you have correctly selected the zones to be assigned to a Thermostat go to the Thermostat and activate its

Initialization (see Thermostat user manual).

3. The green LED of the zone previously selected should now extinct; two squares scrolls on the graphic scope

indicate also a correct initialization.

4. When the Thermostat has been correctly assigned to the selected zones, on the thermostat you can exit the “RF

Init” mode. (don’t forget to switch off the thermostat to avoid perturbation if you need to assign other thermostats)

5. You can repeat the step 1 to 4 to assign other thermostats to the other zones.

6. To exit the “RF init” mode and save this configuration, press (Ok) during 5 sec to return to the main menu.

2/ Master H&C thermostat initialization: WFHT-BASICH&C-BUS or WFHT-LCDH&C-BUS

Use this parameter to configure the Master H&C thermostat with your WFHC-MASTERH&C-BUS.

Once in the parameter’s menu, by pressing several times on the (►) key, go to the “MHc no” parameter, then press the

(+) key to choose the “MHc init” function.

1. When you have correctly selected the “MHc init” function go to the Master H&C Thermostat and activate its

Initialization (see Thermostat user manual).

2. When the Master H&C Thermostat have been correctly assigned with the WFHC-MASTERH&C-BUS, the message

“MHc Yes” must be displayed. Now on the thermostat you can exit the “RF Init” mode. (Don’t forget to switch off the

thermostat to avoid perturbation if you need to assign other thermostats)

Important note

- If the WFHT-BASICH&C-BUS OU WFHT-LCDH&C-BUS must manage a zone(s), it should be also assigned with the

corresponding zone in the “rF init” menu. (Like standard thermostat)

- If two WFHC-MASTERH&C-BUS are installed in the house, the Master H&C thermostat WFHT-BASICH&C-BUS or

WFHT-LCDH&C-BUS should be linked with both WFHC-MASTERH&C-BUS with this submenu to control the totality of

the house. (In this case pay attention to the polarity of the wiring)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Watts WFHC Master H C-Bus slave Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info