Bedienungsanleitung Webasto Cool Top Trail 20-24 (Seite 6 von 24) (Englisch)

802132

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

5 | Installation instructions

6 / 24 9039408D_OI-II_Cool Top Trail 20-24_EN

lThe installation position of the outdoor unit must be con-

sistent with the traveling direction (F) of the vehicle.

lMake sure that there is sufficient room on the inside of the

vehicle to install the air distributor.

lConsider the installation position of the air distributor and

make sure its outlets are at least 400 mm away from cup-

boards, walls and bulkheads which could redirect condi-

tioned air back towards the return air intake. If an outlet is

less than 400 mm from an obstruction, then it should be

sealed closed. Failure to do so will result in a unit that fre-

quently cycles on and off.

lThe cut-out must avoid roof cladding joints where possible.

lChoose an installation position between two longitudinal

supports or sections, if present.

lThere must be a minimum of 100 mm clearance all around

the rooftop unit to ensure suitable air flow and access for

maintenance.

WARNING

When a hatch with safety ventilation function is re-

placed by the air conditioner, you must make sure that

the safety ventilation is restored in another location.

NOTE

The angle of inclination of the air conditioner must not

be greater than 5° (= 8.8%) and the rear of the air con-

ditioner must not be higher than the front.

The following illustrations (Fig. 6, Fig. 7 and Fig. 8) show the re-

quired installation space for the outdoor unit and the air distrib-

utor on the inside for the two different cut-out versions. Centre

the air distributor by using the cut-out.

NOTE

All measurements are in mm, unless stated otherwise.

Fig.6 Installation measurements (top / bottom view)

1 Position of the outdoor unit

2 Position of the air distributor

3 Square cut-out

F Direction of travel

Fig.7 Installation measurements (side view)

Fig.8 Installation measurements (front_view)

5.5 Roof reinforcements

You must reinforce the cut-out with a wooden frame, using

bars which are at least 20 mm wide. You may have to remove

insulation material first however.

The reinforcement frame is to make sure that the roof is not

crushed by the installation bolts and that air conditioned air

does not enter the ceiling space.

Fig.9 Roof reinforcement

1 Roof

2 Wooden bars

Fig.10 Cut-out with wooden reinforcement

1 Cut-out

2 Insulation in roof

3 Wooden bars

5.6 Power supply

WARNING

Danger of electrocution

You must make sure that there is no voltage at electric-

ally operated components before working on them.

Make sure that the mains power supply or the power

supplied by inverters is isolated.

NOTE

Only qualified electricians must make the 230 V elec-

trical connection (in Germany for example, in accord-

ance with VDE 0100, Part 721 or IEC 60364-7-721).

When connecting to the mains supply front, it is the in-

staller’s responsibility to make sure that local wiring

regulations are followed.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Webasto Cool Top Trail 20-24 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Webasto Cool Top Trail 20-24

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info