Bedienungsanleitung Webasto Cool Top Trail 20-24 (Seite 8 von 24) (Englisch)

802132

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

5 | Installation instructions

8 / 24 9039408D_OI-II_Cool Top Trail 20-24_EN

4 Crimp terminals CI-BUS (CI-BUS Unit 2)

5 Housing CI-BUS (CI-BUS Unit 2)

5.8 Adaptor frame installation

1. Make sure the roof is clean, dry and free from oil or grease.

2. Insert the adapter frame into the cut-out to make sure that

the power supply cable and the CI-BUS cable (if applicable)

do not interfere with the frame. If the cables cause obstruc-

tions, then cut or drill openings in the bottom of the frame

to lead the cables through.

3. Confirm the correct orientation of the frame by using the

“This side up” label.

Fig.15 Orientation of the adaptor frame

4. Turn the part over and on the reverse side of “This side up”,

apply silicone sealant uniformly over the path shown.

Fig.16 Sealant paths

5. Turn the part over again and make sure “This side up” is

up. Press down firmly over the installation hole and remove

any sealant that has squeezed out.

Fig.17 Forming an effective seal

5.9 Installing the outdoor unit

Place the outdoor unit over the installed adaptor frame, and ad-

just the position to make sure that the four bolt holes on the

corners are properly aligned.

NOTE

The outdoor unit is heavy. Always have a second per-

son to help carrying the unit.

Do not lift the outdoor unit by the upper white cover.

Lift it by the bottom base.

Using the M8 bolts, verify that the holes of the outdoor unit are

aligned with the holes of the adaptor. If they are not, then re-

position the outdoor unit accordingly.

Do not apply additional sealant between the outdoor unit and

the adaptor frame.

Fig.18 Positioning the outdoor unit

5.10 Connecting the power supply

1. Look upward from inside the vehicle, and locate the ter-

minal block (1).

2. Connect the power supply cable to the 3-pole terminal

block.

3. Match the corresponding active, neutral and the ground

wires.

4. Tighten the screws firmly to make sure that the power lead

is secure and properly connected. Failure to do so may

cause a short circuit or fire.

Fig.19 Location of the terminal block

NOTE

Failure to secure the connections properly may result in

a short circuit or a fire.

5.11 Installing the air distributor

mounting-bracket

1. Prepare the M8 bolts (4), washers (3) and fixing metal

clamping bars (2) as illustrated.

2. Lift the air distributor mounting bracket (1) towards the air

conditioner.

3. Insert the M8 bolts, with its washers, and metal clamping

bars into the 4 corner holes of the air distributor’s mount-

ing bracket.

4. Screw the bolts into their receiving threads by hand to en-

sure proper engagement.

5. Make sure that all bolts are screwed in correctly. Minimally

apply 2 rotations to avoid cross threading.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Webasto Cool Top Trail 20-24 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Webasto Cool Top Trail 20-24

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info