Bedienungsanleitung Webasto Cool Top Trail 20-24 (Seite 15 von 24) (Englisch)

802132

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

Maintenance | 7

9039408D_OI-II_Cool Top Trail 20-24_EN 15 / 24

6.13 Setting the sleep function

The sleep function automatically modifies the target temperat-

ure to provide a comfortable sleeping temperature. This also

helps to reduce compressor run time, energy consumption and

noise levels.

1. Press the SLEEP button to activate the sleep function.

– The icon is displayed in the display of the remote con-

trol to indicate that the sleep function is activated.

– In COOL mode the set temperature will automatically in-

crease in two steps and it will have increased by 2°C

after two hours.

– In HEAT mode the set temperature will automatically de-

crease in three steps and it will have decreased by 3°C

after two hours.

– The sleep function is only available in COOL or HEAT

mode.

2. Press the SLEEP button again to deactivate the sleep func-

tion.

Fig.47 Setting the sleep function

6.14 Changing the units of temperature

Press the °C/°F button to select which units of temperature

units you want to be displayed: Celsius or Fahrenheit.

lYou can do this in any mode.

lThe display on the air distributor follows the selection made

on the remote control.

Fig.48 Celsius / Fahrenheit selection

6.15 Resetting the remote control

To reset the remote control to factory settings:

1. Take out the batteries. and then put them back in. See also

chapter7.2, "Remote control batteries" on page 16.

2. Set the clock again. See chapter6.10, "Setting the system

clock" on page 14.

3. Activate the timer again, if in use. See chapter6.12, "Activ-

ating the timer" on page 14.

Fig.49 Resetting the remote control

6.16 Operating the air distributor

without the remote control

You can control the basic functions of the air conditioner by us-

ing the touch button on the display of the air distributor. This is

useful if you cannot immediately find the remote control or if it

has run out of power.

1. Press the touch button at the air distributor display. With

each press you cycle through the modes: OFF, COOL, FAN,

HEAT.

Fig.50 Setting the operation mode

– In cooling and heating mode the setpoint temperature is

automatically set to 24°C and the fan speed is set to

HIGH.

2. Use the remote control to select any other temperature or

fan speed.

3. You cannot select AUTO mode at the air distributor, but

the display will show the “auto mode” icon in the top right

corner if this has been selected through the remote control.

1 2 3 2

Fig.51 Display on the air distributor

1 Touch button

2 Operation mode symbols

3 Temperature display

6.17 Adjusting the air outlets

Adjust the direction and angle of the air outlet by moving one

blade around its axis. The three blades move together.

Fig.52 Adjusting the air outlets

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Webasto Cool Top Trail 20-24 Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Webasto Cool Top Trail 20-24

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info