Bedienungsanleitung Webasto Cool Top Trail 20-24 (Seite 17 von 24) (Englisch)

802132

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

Troubleshooting | 8

9039408D_OI-II_Cool Top Trail 20-24_EN 17 / 24

8 Troubleshooting

Symptom Action

No air distributor

display when the

unit is turned

ON.

Check if:

lPower is supplied to the vehicle and circuit

breakers are on.

lThe remote control battery is OK.

lThe remote control is off.

lThe voltage is too low.

lThe amperage of the circuit breaker in the

external power supply is too low.

Cooling not

available.

Check that the cooling mode is selected and the air

distributor display shows:

Use the remote control to set required temperature

below the current room temperature.

The compressor will delay a re-start for 3 minutes.

Heating not

available.

Check that heating mode is selected and the air dis-

tributor display shows:

Use the remote control to set required temperature

above the current room temperature.

More time would be needed for starting heating un-

der extremely cold condition.

When the unit is in heating mode and the outside

temperature is very low the unit may automatically

enter defrost mode. The heating will temporarily

stop as the unit warms the outside heat exchanger

to remove any frost & ice. Heating will resume when

the outside heat exchanger has been cleared. During

defrost the unit displays “dF”.

Poor cooling ca-

pacity.

Make sure the filter is clean.

Increase the fan speed to high to obtain the max-

imum capacity.

Make sure all the doors and windows as well as the

sunroof are closed.

Use curtains and awnings to decrease the heat load.

Check that the air openings of outdoor unit are not

soiled or blocked.

Water dripping

out of the air

distributor.

Unblock condensate outlets of outdoor unit.

Check the adaptor frame seal.

Park the vehicle in a more horizontal position, with

an angle < 5° (8,8%).

Increase the fan speed to high if condensate forms

on the outside of the air distributor.

Fault codes on the panel:

- If there is “0” or a jumbled display while on gener-

ator supply this may indicate unstable voltage and

current.

E0 Communication fault.

E1 Room temperature sensor fault.

E2 Indoor heat exchanger temperature sensor fault.

E3 Outdoor heat exchanger temperature sensor fault.

E4 No cooling effect. Possible root causes are:

lInsufficient refrigerant amount due to pip-ing

fracture.

lCompressor fault.

lSensor failure.

E5 Outdoor heat exchanger temperature too high /

Temperature anomaly.

Temperature anomaly: outdoor heat exchanger tem-

perature too high when cooling or too low when

heating. (When cooling, the display of E5 indicates

Symptom Action

the outdoor temperature exceeds 68°C. It is likely

due to the reduction of air flow of the condenser,

poor working of the condenser fan or sensor failure;

when heating, if the outdoor temperature is higher

than 18°C, the external air fan may be on and off

repeatedly. The occurrence of this is not a fault, but

self-protection of the system to avoid overheating of

the unit.)

dF Not a fault: When operating on heating mode in low

ambient temperatures the unit will periodically de-

frost the outside heat exchanger. The air distributor

display shows “dF” during defrost operation and

then returns to heating once the defrost is com-

pleted.

NOTE

Before contacting Webasto for technical support please

collect the following information.

uAre any error codes displayed?

uIs the display of the air distributor in normal opera-

tion or not?

uDoes it display a temperature from 16 to 30°C?

uCan you adjust the set point temperature when in

cool or heat mode?

uIs there a “0” shown in the display?

uIs the display showing a jumbled display?

uWhen in fan mode is there any air flow from the air

distributor outlets?

uCan you hear the compressor starting or stopping in

heating or cooling mode?

ðYour help in collecting this information will greatly

assist the service team help you.

Thank you!

9 Disposal

Dispose of packaging material as required by stand-

ing regulations, separating them for recycling.

When your system has reached the end of its life, you

cannot dispose of the system as regular waste. Make

sure to dispose of the system in accordance with all

local and national applicable rules and regulations.

You can obtain information about disposal at your

local municipality, the responsible waste station, and

your local Webasto sales partner.

Every consumer is legally obliged to dispose of batter-

ies and electronic equipment only in marked recycling

bins at a waste collection point. The return is free of

charge.

See also: chapter7.2, "Remote control batteries" on page 16.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Webasto Cool Top Trail 20-24 Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Webasto Cool Top Trail 20-24

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info