Bedienungsanleitung Webasto Live (Seite 32 von 79) (Deutsch, Englisch, Holländisch, Italienisch, Spanisch)

802116

Zoom out

Zoom in

Vorherige Seite

1/79

Nächste Seite

20 5110326C_OI-II_Webasto Live

Installation cover

7.1 LED indicators

LED-colours Description

Blue Standby

Green Charging

Red Faults

Purple Charging station reset

Yellow Temperature limit

7.1.1 Operating conditions

Fig.8

Operating

indicator

Description

N1 When the charging station is switched on,

this lights up red for 30s, then flashes red-

green-blue at one-second intervals. A beep

sounds if the start-up process is successful.

N2 LED is blue:

Charging station in standby mode; charging

station can be used.

N3 LED is green:

Charging station being used; charging

vehicle.

N4 LED flashes blue at 1 second intervals:

Charging coupling connected to the vehicle,

authentication has not been carried out yet.

N6 LED flashes green at 1 second intervals:

Charging cycle paused by the vehicle

(indicator in configuration can be activated)

7.1.2 Fault conditions

Fig.9

Fault list Description

F1 LED is yellow for 1 s and green for 2 s:

The charging station has become hot and

charges the vehicle with reduced power. After

a cool-down phase the charging station con-

tinues the normal charging cycle.

Fault list Description

F2 LED is yellow and an acoustic signal sounds for

0.5s:

Excess temperature. Charging stopped due to

high temperature within the charging station.

After a cool-down phase the charging station

continues the normal charging cycle.

F3 LED is red and an acoustic signal sounds for

0.5s and then for 5s following a pause:

There is a problem in the voltage or system

monitoring.

DANGER

Danger of fatal electric shock.

uSwitch off and secure the power supply to the

charging station. Only then unplug the cable from

the vehicle.

uContact the Webasto Charging Hotline at

00800-24274464.

Fault list Description

F5 LED flashes red for 1 s at 2 s intervals and an

acoustic signal sounds for 0.5s and then for

5s following a pause:

There is a fault in the vehicle.

uRe-connect the vehicle

uIf the warning persists, contact the car cus-

tomer service.

F6 LED flashes red 2 times, followed by a brief

pause and a buzzer sounds for 0.5 s:

The supply voltage is outside the valid range

of 180 V to 270 V.

uChecking by an authorised electrician.

F7 LED flashes red 3 times, followed by a brief

pause and a buzzer sounds for 0.5 s:

There is a fault in the installation. Info for in-

staller.

7.1.3 Communication statuses

Fig.10

Operating

indicator

Description

C1 LED is blue at 0.5 second intervals:

Operating

indicator

Description

The authorisation process is in progress.

C2 LED lights up red for 1.5/1/0.5s and a

beep sounds at the same time:

Restart of the charging station by RFID

dongle owner/operator (indicator in config-

uration can be activated)

C3 LED lights up red for 0.5s at 60-second in-

tervals:

Information about lost GSM signal (every 60

s in all modes) (indicator in configuration

can be activated)

C5 LED flashes blue for 0.5s and red for 0.5s:

RFID dongle is not permitted by service pro-

vider or charging station.

C6 LED flashes blue for 1s and green for 1s

and a beep sounds:

Authorisation was successful. The vehicle

must be connected to the charging station

within 45s (default value).

C7 LED flashes green at 0.5 second intervals:

Increasing state of charge (SOC) with avail-

able connection using ISO15118, 12.5%

SOC per LED, increasing steadily periodically.

C8 LED is purple for 4 s and an acoustic signal

sounds for 1.5 - 1 - 0.5 s:

Reset by backend.

7.2 Start charging

NOTE

Always take into account the vehicle requirements be-

fore charging a vehicle.

NOTE

Park the vehicle for charging such as to avoid strain in

the charging cable.

Fig.11

The RFID dongle can be authorised before or after the

charging cable is plugged into the vehicle. Note that the

time between authorisation and connection of the char-

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Webasto Live Seite 32

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Webasto Live

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info