Bedienungsanleitung Webasto Next (Seite 8 von 23) (Englisch)

802117

Zoom out

Zoom in

Vorherige Seite

1/23

Nächste Seite

8 | Installation and electrical connection

8 / 23 5111232C OI-II Webasto Next_EN

go to:

https://apps.apple.com/ (Apple App Store) or

https://play.google.com/ (Google Play Store) as appropri-

ate.

Webasto ChargeConnect app (for operation)

To download this app:

scan the QR code below or

go to:

https://apps.apple.com/ (Apple App Store) or

https://play.google.com/ (Google Play Store) as appropri-

ate.

8.1 Requirements installation space

The following points must be taken into account when selecting

the installation location for the Webasto Next:

lThe lower edge of the enclosed mounting template must

be at a minimum distance of 90cm above the ground dur-

ing installation. See Fig. 20.

lIf several charging stations are installed next to each other,

a spacing of at least 200 mm must be maintained between

each station.

lThe mounting surface must be solid and strong.

lThe mounting surface must be completely flat (max. 1 mm

difference between the individual mounting points).

lThe mounting surface must not contain any flammable sub-

stances.

lA cable run from the charging station to the vehicle as

short as possible.

lNo risk of driving over the charging cable.

lPossible electrical connections from infrastructure.

lPavements and escape routes must not be obstructed.

lAn installation location that is protected against direct sun-

light is required for optimum and fault-free operation.

lThe usual parked position of the vehicle, taking account of

the position of the charging plug on the vehicle.

lConsideration of local building and fire protection regula-

tions.

NOTE

The mounting distance between the bottom edge of

the charging station and the floor must be at least

0.9 m.

NOTE

Note the installation kit for country-specific purposes

(see chapter6, "Scope of delivery" on page 7).

8.2 Criteria for the electrical

connection

The maximum charging current is factory set and is indicated on

the type label of the charging station. The maximum charging

current can be adapted to the value of the circuit breaker fitted

during installation using DIP switches.

NOTE

The current value of the selected protective device must

not fall below the current value specified on the type la-

bel for the charging station or the value set using the

DIP switch.

See chapter8.7, "DIP switch settings" on page 11.

The installation requirements for the charging station should be

checked by a qualified electrician before starting connection

works.

Comply with the nationally applicable regulations of the author-

ities and power supply companies, e.g. registration of installa-

tion of a charging station.

NOTE

In some countries, single-phase charging is limited to a

defined current. The local connection requirements

must be observed.

All protective devices specified below must be designed such

that the charging station is disconnected from the grid in the

case of a fault. You must meet national installation regulations

and standards when selecting the protective device.

The maximum charging current is factory set and is indicated on

the type label of the charging station. The maximum charging

current can be adapted to the value of the circuit breaker fitted

during installation using DIP switches.

8.2.1 Dimensioning of the Residual Current

Circuit Breaker (RCCB)

The national installation regulations generally apply. Unless oth-

erwise specified therein, each charging station must be protec-

ted by an appropriate residual current device (RCD type A) with

a trip current of ≤30mA.

8.2.2 Dimensioning of the circuit breaker

The circuit breaker must conform to IEC 60898. The let-through

energy (I²t) must not exceed a maximum 80,000 A²s.

Alternatively, a residual current circuit breaker combination

(RCBO) according to EN 61009-1 can be used. The aforemen-

tioned parameters apply for this circuit breaker combination.

8.2.3 Mains isolation device

The charging station does not have its own main ON/OFF

switch. The protective devices installed in the power supply sys-

tem are therefore also used to disconnect the power supply.

8.3 Installation

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Webasto Next Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Webasto Next

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info