Bedienungsanleitung Webasto Next (Seite 9 von 23) (Englisch)

802117

Zoom out

Zoom in

Vorherige Seite

1/23

Nächste Seite

Installation and electrical connection | 8

5111232C OI-II Webasto Next_EN 9 / 23

1. Take into account the mounting position at the installation

location. See Fig. 20.

2. Remove the drill template from the packaging at the per-

foration.

3. Mark the four positions of the drill holes at the installation

location using the drill template. See Fig. 19 and Fig. 20.

4. Drill 4 holes of Ø 8mm in the marked positions.

NOTE

The central hole (1) should be used for the building wir-

ing system. The hole (2) shown on the left must be used

if the LAN cable is used. See also Fig. 20.

5. Position the bracket over the upper holes and mount using

2 wall plugs and 2 screws, 6x70mm, T25.

6. Remove the lower cover from the connection area of the

charging station.

WCH000018A

Fig.5

Remove the spiral antikink protection from the connection

area of the charging station and place it with the other

supplied material.

For surface mounting, make a recess for routing the lead

on the back of the charging station using the designated

lateral predeterminedbreakingpoints (if necessary deburr

the edge of the break using a round file).

Insert the lead through the designated lead-through and fit

the charging station on the previously mounted bracket.

Mount the charging station using 2 screws, 6x90mm,

T25 using the mounting holes in the lower connection

area. Do not exceed the max. torque of 6Nm (Newton

metres).

8.3.1 Connecting the charging cable

1. Push the spiral antikink protection with the threadless

opening forward over the supplied charging cable.

2. Guide the charging cables through the previously pre-as-

sembled sealing clip.

NOTE

Ensure correct fit of the previously pre-assembled rub-

ber seals in the sealing clip.

3. Push the charging cable at least 10mm beyond the upper

edge of the clamping area of the strain relief clamp.

4. Turn the antikink protection spiral several turns onto the

sealing clip.

NOTE

Do not tighten yet.

WEM000091

Fig.6

5. Screw in the supplied strain relief clamp in the correct posi-

tion on the charging cable.

NOTE

The strain relief clamp has two position options for

charging cable versions 11kW and 22kW.

Ensure that the “11 kW installed” label for an 11 kW

charging cable is visible.

6. Fit the strain relief clamp in the correct mounting position

using the supplied self-tapping Torx screws (6.5x25mm)

and tighten to 5.5Nm. (Attention: Do not overtighten

screws).

7. The strain relief clamp must be flush when securely

screwed in.

NOTE

Perform a tension test on the charging cable to make

sure that the cable cannot move.

8. Screw the antikink protection spiral onto the sealing clip

with a torque of 4Nm.

9. Using the slot-head screwdriver (3.5 mm), connect the indi-

vidual cable ends according to the specification in the illus-

tration (Fig. 8) on the right terminal block with the "OUT"

label.

10. To do this, insert the screwdriver in the designated upper

opening of the spring relief for the terminal block and open

the clamping spring.

11. Now insert the individual wire into the designated connec-

tion opening of the terminal block (lower opening).

12. Then pull the screwdriver out again and perform a tension

test to make sure that the individual wires are clamped

properly and fully.

Charging cable Description

Blue N

Brown L1

Black L2

Grey L3

Yellow-green PE

Black-white Control cable (CP)

10.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Webasto Next Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Webasto Next

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info