Bedienungsanleitung Weber summit s 450 (Seite 9 von 76) (Englisch)

328040

Zoom out

Zoom in

Vorherige Seite

1/76

Nächste Seite

WWW.WEBER.COM

GENERAL INSTRUCTIONS

GAS INSTRUCTIONS

Slide out Bottom tray - Remove excess grease, then wash with warm soapy water,

then rinse.

Flavorizer

bars and Cooking grates - Clean with a suitable stainless steel bristle

brush. As needed, remove from grill and wash with warm soapy water, then rinse with

water.

Catch pan - Disposable foil trays are available, or you can line the catch pan with

aluminum foil. To clean the catch pan, wash with warm soapy water, then rinse.

Thermometer - Wipe with warm soapy water; clean with plastic scrub ball.

Inside cooking module - Brush any debris off of burner tubes. DO NOT ENLARGE

BURNER PORTS (OPENINGS). Wash inside of cooking box with warm soapy water

and a water rinse.

Inside Lid - While lid is warm, wipe inside with paper towel to prevent grease build-up.

Flaking built-up grease resembles paint flakes.

Stainless steel surfaces - Wash with a soft cloth and a soap and water solution. Be

careful to scrub with the grain direction of the stainless steel.

Do not use cleaners that contain acid, mineral spirits or xylene. Rinse well after

cleaning.

Preserve Your Stainless Steel - Your grill or its cabinet, lid, control panel and shelves

may be made from stainless steel. To keep the stainless steel looking its best is a

simple matter. Clean it with soap and water, rinse with clear water and wipe dry. For

stubborn particles, the use of a non-metallic brush can be used.

ƽ IMPORTANT: Do not use a wire brush or abrasive cleaners

on the stainless steel surfaces of your grill as this will cause

scratches.

ƽ IMPORTANT: When cleaning surfaces be sure to rub/wipe

in the direction of the grain to preserve the look of your

stainless steel.

INSTALL GAS SUPPLY

GENERAL SPECIFICATIONS FOR PIPING

Note: Contact your local municipality for building codes regulating outdoor

gas barbecue installations. In absence of Local Codes, you must conform to

the latest edition of the National Fuel Gas Code: ANSI Z 223.1/NFPA 54, or CAN/

CGA-B149.1, Natural Gas and Propane Installation Code. WE RECOMMEND THAT THIS

INSTALLATION BE DONE BY A PROFESSIONAL.

Some of the following are general requirements taken from the latest edition of the

National Fuel Gas Code: ANSI Z 223.1/NFPA 54, or CAN/CGA-B149.1, Natural Gas and

Propane Installation Code for complete specifications.

• This barbecue is designed to operate at 4.5 inches of water column pressure (.163

psi).

• A manual shut-off valve must be installed outdoors, immediately ahead of the

quick disconnect.

• An additional manual shut-off valve indoors should be installed in the branch fuel

line in an accessible location near the supply line.

• The quick disconnect connects to a ½ inch NPT thread from the gas source. The

quick disconnect fitting is a hand-operated device that automatically shuts off the

flow of gas from the source when the barbecue is disconnected.

• The quick disconnect fitting can be installed horizontally, or pointing downward.

Installing the fitting with the open end pointing upward can result in collecting

water and debris.

• The dust covers (supplied plastic plugs) help keep the open ends of the quick

disconnect fitting clean while disconnected.

• Pipe compound should be used which is resistant to the action of natural gas

when connections are made.

• The outdoor connector must be firmly attached to rigid, permanent construction.

ƽ WARNING: Do not route the 10 foot hose under a deck. The

hose must be visible.

GAS LINE PIPING

• If the length of the line required does not exceed 50 feet, use a 5/8" O.D. tube.

One size larger should be used for lengths greater than 50 feet.

• Gas piping may be copper tubing, type K or L; polyethylene plastic tube, with a

minimum wall thickness of .062 inch; or standard weight (schedule 40) steel or

wrought iron pipe.

• Copper tubing must be tin-lined if the gas contains more than 0.3 grams of

hydrogen sulfide per 100 cubic feet of gas.

• Plastic tubing is suitable only for outdoor, underground use.

• Gas piping in contact with earth, or any other material which may corrode the

piping, must be protected against corrosion in an approved manner.

• Underground piping must have a minimum of 18" cover.

TEST CONNECTIONS

All connections and joints must be thoroughly tested for leaks in accordance with local

codes and all listed procedures in the latest edition of the National Fuel Gas Code: ANSI

Z 223.1/NFPA 54, or CAN/CGA-B149.1

ƽ DANGER

Do not use an open flame to check for gas leaks. Be sure

there are no sparks or open flames in the area while you

check for gas leaks. This will result in a fire or explosion

which can cause serious bodily injury or death and damage

to property.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Weber summit s 450 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Weber summit s 450

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info