Bedienungsanleitung Weldkar MIG 2125 INVERTER WELDER (Seite 17 von 44) (Deutsch, Englisch, Holländisch, Französisch)

686265

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

3. INSTALLATION

This must be carried out by skilled personnel. All

connections must be carried out according to current

regulations, and in full observance of safety laws (CEI

reglement 26-10 – CENELEC HD 427).

- Make sure that the supply voltage matches the

voltage indicated on the speciﬁcations plate.

- When mounting a plug, make sure it has an

adequete capacity, and that the yellow/green

conductor of the power supply cable is connected to

the earth pin.

WARNING! Extension cords of up to 30 m must have a

crosssection of at least 2.5 mm².

3.1 DESCRIPTION OF THE EQUIPMENT

1) MIG Welding Torch Adapter (Euro connector).

2) Earth cable output terminal (-)

3) Power switch: control power through and break

4) Shielding Gas Inlet.

5) Power Access client: access to cable

6) Fan: for cooling the machine.

7) Digital display (Voltage).

8) Power indicator: Indicates that the machine is

turned on.

9) The indicator will illuminate if the duty cycle of the

power source has been exceeded.

10) Digital display (Welding current, Wire speed).

11) Indicates that the display (10) shows the MIG

welding wire speed.

12) Indicates that the display (10) shows the welding

current.

13) 2T or 4T mode selection Button.

14) Wave control: Is used to adjust the intensity of the

welding arc.

15) Setting knob: In relation to the selected LED,

regulates: the welding current

(LED 12) or wire speed in MIG welding (LED 11).

16) Setting knob: regulates welding voltage.

3.2 REEL FITTING SEQUENCE

1. Mount the wire reel.

2. The wire reel hub incorporates a friction brake which

is adjusted during manufacture for optimum breaking.

If it is considered necessary, adjustment can be made

by turning the large nut inside the open end of the

hub clockwise to tighten the brake.

3. Use the nut to secure the wire reel.

3.3 WIRE FEED

Make sure that the groove of the rollers matches the

wire diameter used. Mount the wire coil and slip the wire

into the feeder and torch sheath. Remove the gas nozzle

and unscrew the contact tip (located on the end of the

torch). Turn on the machine. Press the torch trigger until

the wire protrudes. Tighten the contact tip and replace

the gas nozzle.

3.4 GAS CONNECTION

- Secure the welding grade shielding gas cylinder

in an upright position by chaining it to a suitable

stationary support to prevent falling or tipping.

- Connect the regulator inlet connection to

cylinder or pipeline and tighten it ﬁrmly but not

excessively, with a suitable spanner.

- Connect and tighten the outlet hose ﬁrmly.

- Open the reducer of the cylinder and adjust the

gas ﬂow to 8 – 10 l/min.

CAUTION: Make sure the gas used is compatible

with the material to be welded.

Figure 1

Figure 3

Gas cylinder

Pressure reducer

Shielding

gas

Welding torch

Power source with

wire feed unit

Earth clamp

Workpiece

8 10

141516

Figure 2

eng

deufra ned

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Weldkar MIG 2125 INVERTER WELDER Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info