Bedienungsanleitung Weller WAD 101 (Seite 25 von 103) (Alle Sprachen)

579835

Zoom out

Zoom in

Vorherige Seite

1/103

Nächste Seite

WP 80 / WSP 80:

The soldering iron WP 80 / WSP 80 is characterized by its

capacity for reachingthe soldering temperature quickly and

precisely. Its slim design and heating power of 80 watts

makes universal usage possible - from extremely fine to

high-temperature soldering work. Work can be continued

immediately after switching soldering tips, since the tempe-

rature is reached again quickly.

See "Accessories" for additional tools.

3. Commissioning

Place the soldering tool in the holder. Insert compressed air

hose with 6 mm outer diameter in the quick action coupling

(12). Provide supply of compressed air with 400 kPa (58 psi)

dry, oil-free compressed air or nitrogen (N2).

Warning:

When using nitrogen, attention must be paid to

satisfactory room ventilation.

Plug the electrical lead from the soldering tool in the 7 pole

socket (7) on the front panel and lock. Connect the compres-

sed air hose to the compressed air connection nipple (8).

Check that the mains voltage matches that on the rating

plate and that the mains switch (1) is in the off position. If the

mains voltage is correct, plug the control unit into the mains.

Warning:

Do not direct hot air soldering tools at people or

inflammable objects.

Switch on the unit at the mains switch (1). When the unit is

switched on, a self-test is performed during which all the

indicators (2) are illuminated. The temperature set (required

value) and the temperature scale (°C/°F) are then briefly dis-

played. The electronics then switch automatically to the dis-

play of the actual value. The red dot (5) on the display (2) illu-

minates. This dot serves as an optical regulation monitor.

Continuous illumination means that the system is heating

up. Flashing indicates that the operating temperature has

been reached.

Setting the temperature

The digital display (2) shows the actual value temperature.

By pressing the UP or DOWN key (3, 4) the digital display (2)

switches to the setpoint. The setpoint can be changed by

tapping or by firmly pressing the UP or DOWN button (3, 4)

in the desired direction. Pressing the button will change the

setpoint quickly. The digital display (2) returns automatically

to the actual value approximately 2 seconds after releasing

the button.

Adjusting the Air Flow Rate

The air flow rate required can be adjusted at the flow control

valve (9). Turning the control valve (9) to the left increases

the flow rate. Air is fed to the hot air soldering tool as long as

the finger operated switch is held down.

Standard setback for control unit WAD 101:

Setting back the set temperature to 150°C. The setback

time, which follows the switching of the soldering station to

standby mode, is 20 minutes. After three setback times

(60 minutes) the ”AUTO-OFF” function is activated. The

soldering tool is switched off (blinking line on the display).

English

Technical Data

Dimensions in mm: 166 x 134 x 101 (L x B x H)

Mains Voltage: 230 V / 50 Hz (120 V / 60 Hz)

Power Consumption WAD 101: 105 W

Power Consumption WAD 101IG: 150 W

Protection Class: 1 (Control Unit) and 3 (Soldering Tool)

Fuse: 230 V: T 630 mA (120 V: T 1,0 A)

Temperature Regulation: °C Version Hot Air 50°C - 550°C

Soldering Iron & inert gas soldering irons 50°C - 450°C

°F Version Hot Air 122°F - 999°F

Soldering Iron & inert gas soldering irons 122°F - 842°F

Precision: Hot Air ± 30°C (± 54°F)

Soldering Iron & inert gas soldering irons ± 9°C (± 17°F)

Flow Rate: Approx. 0 - 10 l/min

Control range of WAD 101IG: approx. 0 - 5 l/min.

Compressed Air: Inlet pressure 400 kPa (58 psi), oil-free, dry compressed air or nitrogen (N2)

Compressed Air Connection: Compressed air hose of 6 mm (0.24") diameter

Inert gas pressure: The inlet pressure is set permanently to 200 kPa by a pressure regulator.

The pressure regulator must not be adjusted.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Weller WAD 101 Seite 25

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info