Bedienungsanleitung Westfire WF36 (Seite 10 von 32) (Deutsch, Englisch, Holländisch, Dänisch, Französisch)

813307

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

WESTFIRE · WF36 WF37

UNIQ 36 and UNIQ36 PEDESTAL dimensions / UNIQ37 and UNIQ37 PEDESTAL dimensions

Stove model Weight Nominal heat output

Wood Smokeless fuels

UNIQ36 / UNIQ37 90 kg 7.2 KW N/A

UNIQ36 Pedestal /UNIQ37 Pedestal 95 kg 7.2 KW N/A

UNIQ37 Large 100 kg 7.2 KW N/A

UNIQ36 / UNIQ37 UNIQ36 Pedestal / UNIQ37 Pedestal UNIQ37 Large

Height 980 mm Pedestal 1: 1150 mm / Pedestal 2: 1070 mm 1310 mm

Width 505 mm 505 mm 505 mm

Depth 445 mm 445 mm 445 mm

Closed combustion option Order speciﬁc closed combustion option

STOVE PERFORMANCE & TESTING

Westﬁre UNIQ36/ WF36 Pedestal and UNIQ37/ WF37 Pedestal have been approved in accordance with EN 13240.

PREPARATORY WORK AND SAFETY CHECKS

IMPORTANT WARNING

This stove must not be installed into a chimney that serves any other heating appliance. There must not be an

extractor fan ﬁtted in the same room as the stove as this can cause the stove to emit fumes into the room.

CHIMNEY

Chimney Connection

Flue Diameter 125 mm

IMPORTANT: Once the stove is unpacked and checked it is necessary to remove the central bar from the ﬂue collar of

the stove before installation. To remove unbolt collar remove bar and replace collar.

When installing your stove with a 125 mm /5” ﬂue please ensure to ﬁll drain hole at rear of cast collar with ﬁre

cement so to prevent any potential leakage of ﬂue gases. Use a proprietary brand of heat resistant ﬁre cement and

ensure that enough cement is used to completely ﬁll the area.

In order for the stove to perform satisfactorily the chimney height must be sufﬁcient to ensure an adequate

draught so as to clear the products of combustion and prevent smoke problems into the room.

Minimum draft: UNIQ36/ WF36 Pedestal and UNIQ37/ WF37 Pedestal stoves has been tested with a draft of

12 Pa. Maximum draft 25 Pa.

Flue gas ﬂow 7.0 g/sec.

Flue gas temperature 303°C. approximately 12 Pa.

NOTE: A chimney height of not less than 4.5 metres measured vertically from the outlet of the stove to the top of

the chimney should be satisfactory. Alternatively the calculation procedure given in BS 5854:1980 may be used as

the basis for deciding whether a particular chimney design will provide sufﬁcient draught.

The outlet from the chimney should be above the roof of the building in accordance with the provisions of Building

Regulations Approved Document J.

If installation is into an existing chimney then it must be sound and have no cracks or other faults which might allow

fumes into the house. Older properties, especially, may have chimney faults or the cross section may be too large

i.e. more than 160 mm x 160 mm. Remedial action should be taken, if required, seeking expert advice, if necessary.

If it is found necessary to line the chimney then a ﬂue liner suitable for solid fuel must be used in accordance with

Building Regulations Approved Document J.

Any existing chimney must be clear of obstruction and have been swept clean immediately before installation of the

stove. If the stove is ﬁtted in place of an open ﬁre then the chimney should be swept one month after installation to

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Westfire WF36 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info