Bedienungsanleitung Whirlpool BIWDWG961484EU (Seite 3 von 4) (Englisch)

756834

Zoom out

Zoom in

Vorherige Seite

1/4

Nächste Seite

Drying only

Press button “” to perform the drying-only cycle. After selecting the

desired cycle (compatible with the type of garments), press button “”

to exclude the washing phase and start the drying phase at the maximum

level for the selected cycle. The drying level or time may be set and

changed by pressing the drying button “ ”.

CHILD LOCK

to lock the control panel, press and hold the button “ ” for

approximately 3 seconds. the symbol lights on the display to indicate

that the control panel is locked (with the exception of the button). This

prevents unintentional changes to programmes, especially with children

near the machine.

If any attempt is made to use the control panel, the symbol ashes on

the display.

To unlock the control panel, press and hold the button “” for

approximately 3 seconds.

TIPS AND SUGGESTIONS

Divide the laundry according to:

Type of fabric (cotton, mixed bres, synthetics, wool, garments to be

hand-washed). Colour (separate coloured garments from whites, wash

new coloured garments separately). Delicates (small garments – such as

nylon stockings – and items with hooks – such as bras: insert them in a

fabric bag).

Empty the pockets:

Objects such as coins or lighters can damage the washing machine and

the drum. Check all buttons.

Follow the dosage recommendation / additives

It optimizes the cleaning result, it avoids irritating residues of surplus

detergent in your laundry and it saves money by avoiding waste of surplus

detergent

Use low temperature and longer duration

The most ecient programmes in terms of energy consumption are

generally those that perform at lower temperatures and longer duration.

Observe the load sizes

Load your washing machine up to the capacity indicated in the

“PROGRAMME CHART” table to save water and energy.

Noise and remaining moisture content

They are inuenced by the spinning speed: the higher the spinning speed

in the spinning phase, the higher the noise and the lower the remaining

moisture content.

CARE AND MAINTENANCE

Before performing cleaning and maintenance, switch the washing machine

o and disconnect it from the mains power. Do not use ammable liquids to

clean the washing machine. Clean and maintain your washer - dryer

periodically (at least 4 times per year).

Disconnect the water and power supplies

Close the water tap after every wash. This will limit wear on the hydraulic

system inside the washing machine and help to prevent leaks.

Unplug the washing machine when cleaning it and during all

maintenance work.

Clean the washing machine

The outer parts and rubber components of the appliance can be cleaned

using a soft cloth soaked in lukewarm soapy water. Do not use solvents or

abrasives.

Clean the detergent dispenser drawer

Wash it under running water; this operation should be repeated

frequently.

Care for the door and drum

Always leave the porthole door ajar in order to prevent unpleasant

odours from forming.

Check the water inlet hose

Check the water inlet hose at least once a year. If it is cracked or broken, it

must be replaced: during wash cycles, the high pressure of the water

could suddenly split the hose open.

! Never use hoses that have already been used.

Cleaning the water lter / draining residual water

Switch o and unplug the washing machine, take out the kitchen plinth before

cleaning the water lter or draining residual water.

The kitchen plinth must be mounted back all the time once the cleaning

operation is over.

If you used a hot wash programme, wait until the water has cooled down

before draining any water. Clean the water lter regularly, to avoid that the

water cannot drain after the wash due to obstruction of the lter. If the water

cannot drain, the display indicates that the water lter may be clogged.

1 . Place a container close to the pump to collect any spillage.

2 . Remove, pulling it out, the “emergency drain hose” from the base of

the washing machine .

Remove the stopper of the “emergency drain hose” at the end of the hose

and let the water ow into the container.

3 . Turn the exhaust lter handle and pull it out of the housing .

When the container of plinth is full with water, plug the stopper to the

hose end, and reinsert the small hose in the washing machine’s base . After,

empty the container .

Afterwards rmly close the emergency drain hose with the stopper .

4. Remove lter: Lay a cotton cloth beneath the water lter, which can

absorb a small amount of rest water . Then remove the water lter by

turning it out anticlockwise .

5 . Clean the water lter: remove residues in the lter and clean it under

running water .

6 . Insert the water lter: Reinsert the water lter again by turning it in

clockwise direction . Make sure to turn it in as far as it goes; the lter handle

must be in vertical position . To test water tightness of the water lter, you

can pour about 1 liter of water into the detergent dispenser .

Then reinstall the kitchen plinth.

LOAD BALANCING SYSTEM

Before every spin cycle, to avoid excessive vibrations before every spin and

to distribute the load in a uniform manner, the drum rotates continuously

at a speed which is slightly greater than the washing rotation speed. If,

after several attempts, the load is not balanced correctly, the machine

spins at a reduced spin speed. If the load is excessively unbalanced, the

washing machine performs the distribution process instead of spinning. To

encourage improved load distribution and balance, we recommend small

and large garments are mixed in the load.

TRANSPORT AND HANDLING

Do not lift the washing machine by gripping it from the upper section.

Unplug the appliance and close the water tap. Check that the door and

detergent dispenser drawer are tightly closed. Detach the lling hose

from the water tap then detach the drain hose. Empty all the water

remaining in the hoses and secure the latter so that they do not get

damaged during transport. Apply the transport bolts back on. Repeat, in

reverse order, the transport bolt removal procedure described in the

“Health & Safety and Installation Guides”.

Whirlpool BIWDWG961484EU Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Whirlpool BIWDWG961484EU

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info