Bedienungsanleitung Whirlpool Seattle 1400 (Seite 7 von 13) (Englisch)

528407

Zoom out

Zoom in

Vorherige Seite

1/13

Nächste Seite

Door seal

• Dry the door seal after each washing with an

absorbent cotton cloth; make sure that the door

seal is completely dry before closing the door of

the empty washing machine.

• Check the condition of the door seal periodically.

Filter

• Check and clean the filter regularly, at least two

or three times a year (see “Draining Residual

Water/Cleaning The Filter”).

Do not use flammable fluids for cleaning

the appliance.

GB 7

Appliance exterior and control panel

• Clean with a soft damp cloth.

• If necessary, use some soapy water or a mild

neutral detergent (do not use detergents containing

solvents, abrasive detergents, window or general-

purpose cleaners - they may harm the surfaces).

Appliance interior

• After each washing, leave the door open for some

time to allow the inside of the appliance to dry.

• If you never or seldom wash your laundry at

95°C, we recommend to occasionally run a 95°C

programme without laundry, adding a small

amount of detergent, to keep the interior of the

appliance clean.

CARE AND MAINTENANCE

Water inlet hose(s) (picture C, D or E - depending on

model)

Check the inlet hose regularly for brittleness and cracks and replace it

if necessary using a new hose of the same type.

The inlet hose as shown on picture “D” has a safety valve to prevent

the appliance against uncontrolled water inlet; if the safety valve

inspection window is red, the safety valve has been activated and the

hose must be exchanged. Contact out After-Sales Service or your

specialist dealer to obtain a new inlet hose. For unscrewing the inlet

hose as shown on picture “D”, you must push down the release lever

while unscrewing it.

If your inlet hose has a transparent hose coating (pict. “E”), periodically

check the colour of the transparent coating. If the transparent hose

shows a local dark colour change, this is an indication that the hose

may have a leak and should be replaced. Contact our After-Sales Service

team or specialist dealer to obtain a replacement hose.

Cleaning the mesh filter in the water inlet hose(s)

1. Close the tap and loosen the inlet hose on the tap.

2. Clean the internal mesh filter and screw the water inlet hose

back onto the tap.

3. Now unscrew the inlet hose on the rear of the washing machine.

4. Pull off the mesh filter from the washing machine connection

with universal pliers and clean it.

5. Refit the mesh filter and screw the inlet hose on again.

6. Turn on the tap and ensure that the connections are completely

water-tight.

Safety valve

inspection

window

Cleaning the detergent dispenser

1. Pull out the dispenser drawer until it stops.

Press with your finger on the space of the siphon being marked

with “PUSH” (picture “A”) to release the drawer and pull it out

completely.

2. Remove the siphon from the softener chamber by pulling it

upwards (picture “B”).

3. Wash all the parts under running water.

4. Clean the dispenser compartment with a damp cloth.

5. Refit the siphon in the softener chamber by pushing it down until

it stops; then push the dispenser drawer back into the dispenser

compartment.

PUSH

Release

lever

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Whirlpool Seattle 1400 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Whirlpool Seattle 1400

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info