Bedienungsanleitung Whirlpool W11OS14S2P (Seite 30 von 32) (Englisch)

756880

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

TROUBLESHOOTING

Problem Possible cause Solution

The oven is not

working.

Power cut.

Disconnection from the

mains.

Check for the presence of mains electrical power and

whether the oven is connected to the electricity supply.

Turn off the oven and restart it to see if the fault persists.

The display shows

the letter “F” followed

by a number or letter. Oven failure.

Contact you nearest Client After-sales Service Centre

and state the number following the letter “F”.

Press , tap ”Info” and then select “Factory Reset”. All

settings saved will be deleted.

The home power

goes off. Power setting wrong.

Verify if your domestic network has at least a rating of

more than 3 kW. If no, decrease the power to 13 Ampere.

To change it, press , select “More Modes” and then

select “Power Management”.

The function does

not start.

The function is not

available in demo

mode.

Demo mode is running. Press , tap “Info” and then select “Store Demo

Mode” to exit.

The door will not

open. Cleaning cycle in progress. Wait for the function to finish and for the oven to cool

down.

The icon is shown

on display.

The WiFi router is off.

The router settings have

changed.

The wireless connections

does not reach the

appliance.

The oven is unable

to establish a stable

connection to home

network.

The connectivity is not

supported.

Check that the WiFi router is connected to the Internet.

Check that the WiFi signal close to the appliance is

strong.

Try to restart the router.

See the “WiFi FAQs” section.

If your home wireless network settings have changed,

connect to the network: Press , tap “WiFi” and then

select “Connect to network”.

Connectivity is not

supported. Remote operation is not

permitted in your country. Check whether your country allows remote operation of

electronic appliances before purchasing.

The touch screen

display is not

working properly.

Prolonged use.

Overload system.

Press and hold for at least 4 seconds. Switch the

oven on and see if the fault persists.

Water is not drawn

from the inlet pipe

The pipe is not correctly

inserted.

The pipe is obstructed.

Unplug the pipe.

Check that the pipe is not obstructed.

Insert again the pipe, being careful to perform the

operation in the proper way (check the orientation of

the pipe: the push button has to be oriented to the left

but not pressed, and you must hear a click when fully

inserted).

The display shows

“ERROR” during the

Drain function

The Drain function is not

working properly Contact the After Sales Service

Can’t see your

favorites? System needs to be

refreshed.

Run the Factory Reset (Press , tap “Info” and then

select “Reset product”). Once this operation is

completed, you can easily save and view your favorite

cycles.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Whirlpool W11OS14S2P Seite 30

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Whirlpool W11OS14S2P

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info