Bedienungsanleitung Whirlpool WHBSC92FLTX (Seite 23 von 168) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Norwegisch)

756917

Zoom out

Zoom in

Vorherige Seite

1/168

Nächste Seite

SAID … … … … … … … … … …

1.2 PROVISIONING

• Before starting the installation process turn on your router and verify that the wireless signal of your home router is reaching the

appliance. To verify the Wifi strength signal use a Tablet or Smart-phone connected only to the Wi-Fi router, disable any other

data connections, and place the device close to the appliance. Open any internet web page in a browser and check that it is

downloaded fast correctly. If the internet connection of your home is working correctly but the page is not downloaded, you may

need to install a Wi-Fi extender device (not provided with the appliance).

• If the router supports WPS 2.0 (or subsequent versions), follow the automatic configuration procedure to connect the device to

the router. If the router doesn’t support WPS, follow the manual configuration procedure.

Follow the instructions on your Whirlpool 6th Sense Live application on your smartphone to connect the appliance to your

wifi network.

Otherwise read the next paragraphs for automatic or manual connection.

1.2.1 AUTOMATIC SETUP INSTRUCTION (FIRST TIME USE) – WPS METHOD

This procedure is applicable only if your router supports WPS2.0 (or greater)

1. On your appliance activate the provisioning process by pressing and hold for three seconds the connectivity button (an

acoustical feedback is played). The appliance is being set to a “search” mode for a local network. The Connectivity icon on the

appliance starts blinking fast.

2. On wireless router press the WPS button to establish a connection between the two products. An indicator light on your router

will begin blinking.

3. When the appliance successfully connects to the local router, the wifi icon switches from fast to slow blinking (supported not in

all appliances).

4. The device will try to connect to the backend system. The connectivity icon remains continuously lit. If the Wi-Fi icon doesn't

stop flashing after a few minutes, this means the device was not able to make a connection with the home network through

WPS. Try repeating the procedure, and if it is unsuccessful, use the manual configuration procedure.

5. You can abort the WiFi connection procedure by pressing the connectivity button.

1.2.2 INSTRUCTIONS FOR MANUAL CONFIGURATION (FIRST USE) - MICRO ACCESS POINT METHOD

This procedure uses Micro Access Point technology and can be used with routers that do not support WPS.

2 Before starting the configuration procedure, note the name (SSID) and password of the home wireless network and the SAID

code of the device. This information will be needed during the installation procedure.

3 Turn the router on, check that the internet connection is active and connect your smartphone/tablet to your Wi-Fi network.

4 On the device, activate the recognition process by pressing the connectivity key for 5 seconds (two acoustic signals will be

emitted as confirmation, the first after 3 seconds, the second after 5 seconds) • the Wi-Fi network icon should start flashing on

the device’s interface.

5 Scan the QR code shown on the label attached to the device; at this point, the Whirlpool 6th Sense Live app will provide

detailed instructions on how to carry out the procedure. Note: In some cases, the app may ask you to specify the type of device:

in this case, select Hood

6 Once the connection has been made, the Wi-Fi icon on the device should stop flashing and remain continuously lit. If not,

disconnect and then reconnect the device to the mains power and repeat the procedure.

7 The configuration procedure is complete.

1.3 SWITCH OFF / ON WI-FI FEATURE

To switch off the connection of the appliance to the wifi network, press and hold for 5 seconds the connectivity button on the

appliance (one acoustical feedback is played). The wifi icon on the appliance display should turn off.

To turn on again the wifi connection on the appliance, press the wifi button on the remote control.

When appliance is provisioned, user can disengage this function and disconnect it from the wifi network by pressing and hold for 10

seconds the connectivity button on the appliance (two acoustical feedbacks are played, one after 5 seconds, one after 10 seconds).

The wifi icon on the appliance display should turn off.

To connect the appliance again to the home wifi network follow the procedure on paragraph “provisioning”.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Whirlpool WHBSC92FLTX Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info