Bedienungsanleitung Whynter ARC-101CW (Seite 11 von 18) (Englisch)

727493

Zoom out

Zoom in

Vorherige Seite

1/18

Nächste Seite

OPERATION INSTRUCTIONS

BEFORE USING YOUR APPLIANCE

 Remove the exterior and interior packaging

 Before connecting the appliance to a power source and operating, let the unit stand upright for a minimum of 4

hours. This will reduce the possibility of a malfunction in the cooling system from handling during transportation.

SWITCHING ON/OFF THE AIR CONDITIONER

The appliance can be switched ON or OFF by pressing the POWER button on the control panel or the ON/OFF but-

ton on the remote control

COOLING MODE

In this mode, the air conditioner cools and dehumidifies the room. To activate this function mode, press the Mode

Control until the Cooling indicator light comes on. When the cooling mode is set, the compressor will start in ap-

proximately 3 minutes. In cooling mode, hot air is exhausted from the outdoor exhaust port and the exhaust hose

must be connected to exhaust out the hot air.

The temperature setting range of this air conditioner is from 61°F / 16°C to 89°F / 32°C. To set the temperature,

press the or buttons. This air conditioner has a 5°F temperature cushion which if the set temperature is within

5°F of the ambient temperature, the unit runs on fan only mode. This saves energy and prolongs the life of the com-

pressor of the air conditioner.

To set the fan speed, press the FAN button. In cooling mode, the difference in noise level between the 3 fan speeds

is not very noticeable when the compressor is on. Try setting the unit to Fan only mode, you should be able to hear

the difference between high and low fan speed settings.

DEHUMIDIFYING ONLY MODE

In this mode, the air conditioner only dehumidifies the room, the compressor will activate intermittently depending on

the ambient temperature and the fan speed is set to LOW. To activate this function mode, press the Mode Control

until the Dehumidifying indicator light comes on. Please note that when switching functions, there will be an

approximate 3 minute transition time. In dehumidifying mode, the exhaust hose does not need to be vented. If the

exhaust hose is vented, the room will be cooled as it dehumidifies. To prevent cooling, remove the exhaust hose

from the window kit and allow the warm air from the rear to be re-circulated into the room. If room temperature is

higher than 77°F, the fan speed can be adjusted. If room temperature is lower than 77°F, the fan speed is set at

Low.

NOTE: When using Dehumidifying mode, venting the exhaust hose to the outside is not required. If vented, the

warm air is exhausted to the outside and cooling within the room may occur. Additionally, if the exhaust hose is not

vented, the unit may require more frequent draining. The air conditioner does not have a humidistat in which a

specific humidity level can be set.

FAN ONLY MODE

In this mode, only the fan of the air conditioner runs and circulates the air in the room. To activate this function mode,

press the MODE button until the Fan indicator light comes on. In this function mode, the temperature cannot be set.

Subsequently, set the desired fan speed by pressing the Fan button. Fan Only mode does not require the use of the

exhaust hose.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Whynter ARC-101CW Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info