Bedienungsanleitung Whynter ARC-143MX (Seite 12 von 19) (Englisch)

643513

Zoom out

Zoom in

Vorherige Seite

1/19

Nächste Seite

12 | P a g e

OPERATION

INSTRUCTIONS



BEFORE USING YOUR PORTABLE AIR CONDITIONER



Remove the exterior and interior packaging.

 Before connecting the unit to the power source, let it stand upright for approximately 4

hours. This will reduce the possibility of a malfunction in the cooling system from handling

during transportation.

SWITCHING ON/OFF THE AIR CONDITIONER

 The unit can be switched ON or OFF by pressing the Power button on the control panel

or the Power button on the remote control.

COOLING MODE

 In this mode, the air conditioner cools and dehumidifies the room. To activate this function

mode, press the Mode Control button until the indicator comes on. When the cooling

mode is set, the compressor will start in approximately 3 minutes.

NOTE: In cooling mode, hot air is exhausted from the outdoor exhaust port and the exhaust

hose must be connected to exhaust out the hot air.

 The temperature setting range of this air conditioner is from 61°F to 89°F. To set the

temperature, press the + or - buttons. This air conditioner has a 5°F temperature cushion

which if the set temperature is within 5°F of the ambient temperature, the unit runs on fan

only mode. This saves energy and prolongs the life of the compressor of the air

conditioner. Once the set temperature is achieved, the fan runs continuously.

 To set the fan speed, press the Fan Speed button. In cooling mode, the difference in

noise level between the 3 fan speeds is not very noticeable when the compressor is

on. Try setting the unit to Fan only mode, you should be able to hear the difference

between high and low fan speed settings.

DEHUMIDIFYING MODE

 In this mode, the air conditioner only dehumidifies the room, the compressor will activate

intermittently depending on the ambient temperature and the fan speed is set to LOW. To

activate this function mode, press the Mode Control button until the indicator comes on.

Please note that when switching function mode, there will be an approximately 3 minute

transition time. In dehumidifying mode, do not connect the exhaust hose and let the warm air

return to the room. If room temperature is higher than 77°F, the fan speed can be adjusted. If

room temperature is lower than 77°F, the fan speed is set at Low.

NOTE: When using the Dehumidifying mode, the air exhaust hose should not be vented to

the outside. If the warm air is exhausted to the outside, cooling may occur. Additionally, you

must manually drain the water from the unit.

FAN ONLY MODE

 In this mode, only the fan of the air conditioner runs and circulates the air in the room. To

activate this function mode, press the Mode Control button until the

indicator comes

on.

In this function mode, the temperature cannot be set. Subsequently, set the desired

fan speed by pressing the Fan Speed button. Fan Only mode requires that the exhaust

hose be removed.

NOTE: The unit does not need to be vented in Fan Only mode.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Whynter ARC-143MX Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info