Bedienungsanleitung Wiesba WB9L (Seite 12 von 88) (Holländisch)

816532

Zoom out

Zoom in

Vorherige Seite

1/88

Nächste Seite

ENGLISHen

If performance diminishes, recharge the battery

pack.

Instructions on charging the battery pack can be

found in the operating instructions of the Metabo

charger.

Li-Ion battery packs "Li-Power" have a capacity and

signal indicator (14):

- Press the button (15), the LEDs indicate the

charge level.

- If one LED is flashing, the battery pack is almost

flat and must be recharged.

Removing and inserting the battery pack

Removal: Press the battery pack release button

(11) and pull the battery pack (13) forwards.

To insert: Slide the battery pack (13) in until it

engages.

Installation of belt hook

Attach the belt hook (12) as shown.

7.1 Setting the direction of rotation,

engaging the transporting safety device

(switch-on lock)

Only activate the rotation selector switch (4)

when the motor has completely stopped.

See page 2:

R= Clockwise setting

L= Counter-clockwise setting

0= Central position: transportation lock setting

(switch-on lock)

7.2 Select the gear (depending on features)

Select the required gear by rotating the thumb

wheel (3).

Change speed only when the machine is in the

process of running down

(briefly switch On and Off).

1. st gear (low speed, high torque) e.g. for

screwdriving, drilling

2. nd gear (high speed) e.g. for drilling

7.3 Presetting the speed (depending on

features)

Select the maximum speed using the preselection

wheel (5). For recommended rotational speeds for

drilling, see figure E, page 3.

7.4 On/Off switch, modifying the speed

Switching on, speed: press the trigger switch (6).

Press in the trigger to increase the rotational

speed.

To switch off release the trigger switch.

Continuous activation: With the trigger (6)

pressed, push in the locking button (7) and

release the trigger. Press and release the trigger

(6) again to switch off.

In continuous operation, the machine

continues running if it is forced out of your

hands. Therefore, always hold the machine with

both hands using the handles provided, stand

securely and concentrate.

7.5 Tool Change with Futuro Top Keyless

Chuck (1)

See illustration A on page 2.

Opening the drill chuck: Hold the retaining ring

and turn the sleeve with your other hand in

direction of the arrow -1-.

Clamping the tool: Insert the tool -2- as far as

possible. Hold the retaining ring and turn the sleeve

as far as it will go with your other hand in direction of

the arrow -3-.

7.6 Tool Change with Futuro Plus Keyless

Chuck (9)

See illustration B on page 3.

Opening the drill chuck:

Turn the sleeve in the direction of the arrow -1-.

The grating sound which may be heard after

opening the drill chuck is functional and is stopped

by turning the sleeve in the opposite direction.

If the chuck is extremely tight: Remove battery pack

/ pull mains plug. Hold the chuck using an open-end

spanner at the flats on its head, and turn the sleeve

vigorously in the direction of the arrow -1.

Clamping the tool:

- Insert the tool -2- as far as possible.

- Turn sleeve in direction -3- until the noticeable

mechanical resistance has been overcome.

-Caution! The tool is not yet clamped! Keep

turning the sleeve (it must "click" when

turning), until it cannot be turned any further -

only now is the tool securely clamped.

With a soft tool shank, retightening may be required

after a short drilling period.

7.7 Unscrewing the chuck

(To screw without a chuck or when using

attachments)

Note: If a bit clamping bush (order no. 6.31281) is

attached, the screwdriver bit inserted in the

hexagon socket of the spindle is held in place.

Futuro Top Keyless Chuck (1)

See page 3, figure C.

Hold the drill spindle tight with the supplied open-

ended spanner. Clamp an Allen key in the chuck

and strike lightly with a rubber hammer to loosen,

then unscrew.

Tighten just as firmly.

The chuck must be screwed firmly to the

spindle. If rotated counter-clockwise (e.g.

when screwing) it could otherwise become loose.

Futuro Plus Keyless Chuck (9)

See illustration D on page 4.

Undo the locking screw. Caution left-handed

thread!

7. Use

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Wiesba WB9L Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info