Bedienungsanleitung Winix U300EU (Seite 7 von 30) (Deutsch, Englisch, Holländisch)

690081

Zoom out

Zoom in

Vorherige Seite

1/30

Nächste Seite

FILTER REPLACEMENT

CAUTION: Turn off the air clearner

and unplug the electrical cord before

performing any maintenance.











Filter Replacement

• The CHECK FILTER indicator will

signal when to replace the entire Filter

Cassette. The replacement period will

vary depending on the hours of usage, air

quality, and location of the unit. However,

in most cases of normal use the filter will

need to be replaced annually.

• Change the Filter Cassette when the

CHECK FILTER indicator is on.

• This filter should be disposed of when

changed.

Filter Cassette Replacement

1. Turn off the air cleaner and unplug the

electrical cord.

2. Remove the front panel by pulling gently

from the lower portion of the panel. Do not

force, the panel should remove easily.

3. Remove the Filter Cassette by gently

pulling out from the bottom and down

from the top.

4. Remove the plastic wrap from the filter.

5. Install the Filter Cassette by inserting tabs

up into the air cleaner and gently pushing

in at the bottom tab until the frame fits into

place snuggly.

6. Replace the front panel by hooking the

panel on the top of the unit. Swing the

panel in by pushing gently on each side of

the unit and then lock it into place.

7. Plug in air cleaner and press POWER

button until short “beep” sounds.

8. Press the RESET FILTER button by gently

inserting a paperclip into the RESET

FILTER hole on the control panel. The light

will flash 5 times before a “beep” sounds

to indicate the filter has been reset. See

figure C on page 8 or Diag. 9 to the right.

The air cleaner will take 3-4 minutes to

calibrate the AIR QUALITY sensor. During

this time the sensor lights will flash on and

off. Once the sensor has calibrated, the

lights will stop flashing and the unit will begin

in AUTO mode.

OPERATIONS

CONTROL PANEL

A. AIR QUALITY SENSOR: Automatically monitors the air quality level and adjusts fan speed

accordingly in Auto.

B. AUTO Mode: Changes the mode setting to AUTO.

C. RESET: Resets the CHECK FILTER indicator light.

D. CHECK FILTER: Signals when to replace filters.

E. PlasmaWave™: Shows that PlasmaWave™ Technology is active.

F. AIR QUALITY: Green, yellow, and red lights indicate the quality of the air.

G. Turbo / High / Med / Quiet: Shows current fan speed setting.

H. SPEED: adjusts fan speed to QUIET, MED, HIGH or TURBO.

I. : Turns the unit On and Off.

J. LIGHT SENSOR: dims the control panel lights and sets the fan speed to QUIET when the

room is dark.

AUTO Mode: The unit is set to AUTO mode when it is first turned on. The air cleaner will actively

monitor the air and adjust the fan speed accordingly to quickly remove any impurities detected.

When the room is dark, the light sensor will automatically switch the unit to QUIET fan speed and

dim the control panel lights.

MANUAL OPERATION: After you turn on the unit, you can switch to manual operation by using

the SPEED button. To go back to the automatic operation press AUTO.

QUIET, MED OR HIGH: These levels are recommended for standard daytime use. HIGH will

activate automatically when sensors detect poor air quality in AUTOMATIC OPERATIONS. Use the

SPEED button to select the required level.

TURBO: This is the highest fan speed. It can be activated manually for maximum air purification

by pushing the SPEED button until the light by Turbo is illuminated.

PlasmaWave™: Push the Auto button for 3 seconds to turn on or off.



Filter Replacement and Cleaning

Filter Service life Cleaning Cycle How to clean

Washable

Pre filter

12 month

every 3 month

Washable

HEPA filter

12 month every 3 month

Washable AOC™

Carbon filter

12 month every 3 month

Filter

Cassette

12 month

Clean with vacuum cleaner or soft brush, Use a

lukewarm water when the filter is very dirty

Put the filter into the lukewarm water for

30 minutes and dry it out in the shade for 24 hours

Put the filter into the lukewarm water for

30 minutes and dry it out in the shade for 24 hours

11 12

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Winix U300EU Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info