Bedienungsanleitung Winora Algemene (Seite 102 von 140) (Englisch)

638065

102

Zoom out

Zoom in

Vorherige Seite

1/140

Nächste Seite

Now you can move the handlebar/stem unit up and down as a whole. Be

sure not to pull out the stem too far. The mark on the stem (max., min.,

max., stop, limit or the like) should always remain within the tube (a). Setting

the stem to a lower position can only add to your safety!

Straighten the handlebars so that they are symmetrical with respect to the

front wheel (b).

Retighten the expander bolt with a torque wrench. Tighten carefully by ap-

proaching the prescribed maximum torque in small steps (0.5 Nm incre-

ments) whilst constantly checking the proper fit of the component. Never

exceed the maximum tightening torque indicated by the manufacturer!

Make sure the stem is firmly fixed by taking the front wheel between your

legs and trying to turn the handlebars and stem relative to the wheel (c). If

there is movement, please increase the tightening torque.

If the handlebars are still too high or too low, you can replace the stem. This

can be quite a big job, as it may mean taking off and remounting all the

fittings on the handlebars. Inform yourself at your bicycle dealer about the

various stem types available. Let the bicycle dealer advise you about the dif-

ferent types of stems and have the stem mounted in the shop.

Never ride a bicycle with a stem drawn out beyond the mark for

the maximum permissible height! Check all bolted connections

and do a brake test before you set off!

Stems come in most different lengths and shaft and binder tube

diameters. If you opt for a stem of inappropriate sizing, handle-

bars and stem may break and result in an accident.

14.2.3 Stems for Threadless Systems, the Aheadset

-System

(*Aheadset

is a registered trade mark of Dia-Compe)

On bicycles with Aheadset

the stem also serves to adjust the initial head-

set bearing pressure. If you change the position of the stem you have to

readjust the bearings (see chapter “Headset”). The vertical setting range is

determined by the intermediate rings, also referred to as spacers (d). In the

case of flip-flop stem models the stem can be mounted the other way round

to achieve a different handlebar height.

This adjustment is a job best left to your bicycle dealer!

14.2.4 Adjusting Adjustable Handlebar Systems (A.H.S.)

Check whether the clamping area (a) of the A.H.S. is accurately centred in

the handlebar clamp of the stem.

Adjust the A.H.S. tilt to your personal needs.

Tighten the handlebar clamping bolt(s) at the stem to the tightening torques

prescribed by the stem manufacturer (b).

Bring the A.H.S. grips into a position that matches your personal needs. To

do so release the clamping bolts at the joint.

After you have found the ideal position for you, retighten the clamping bolts

Adjust the shift/brake levers and grips on the handlebars to your wishes.

Slide the expander cones of the bar ends onto the outer ends of the A.H.S.

Make sure the clamping surfaces are always clean and free of

grease!

Position the bar ends to your personal needs.

Tighten the clamping bolts of the bar ends to a tightening torque of 23 Nm.

Do not forget to insert the according plugs into the ends of the A.H.S. (d).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Winora Algemene Seite 102

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Winora Algemene

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info