Bedienungsanleitung Wodtke Frank Airplus S4 (Seite 32 von 83) (Englisch)

813077

Zoom out

Zoom in

Vorherige Seite

1/83

Nächste Seite

Bedienungsanleitung Steuerung S4_2006_09_25-neu.doc Page 32 / 83

Error code Cause of error How to correct error

LM Er1 =

Broken air flow sensor

Case A:

broken air flow sensor (= component error)

Case B: external error through flue gas reversal.

Temperature of sensor element > 120 °C (see also

error description for TL). If sensor heats up to > 120

°C as a result of flue gas reversal, this is interpreted

as a component error (breakage) and the message

“LM Er1” appears. If the sensor is not permanently

damaged, you can switch the appliance on again as

soon as the appliance or sensor has cooled off

again.

Case A:

Replace air flow

sensor + reset via I/O key.

Case B: No need to replace air

flow sensor. Search for rectify

external error (see error

concerning TL for possible

causes) + reset via I/O key.

LM Er2 =

Short circuit in air flow

sensor

Short circuit = component error Test air flow sensor and

replace if necessary + reset via

I/O key.

TR Er1 =

Flue gas sensor broken Breakage = component error Test TR sensor and replace if

necessary + do manual reset

via I/O key

TR Er2 =

Short circuit in flue gas

sensor

Short circuit = component error Test TR sensor and replace if

necessary + do manual reset

via I/O key

TP Er1 =

Pellet chute sensor

broken

Breakage = component error Test TR sensor and replace if

necessary + do manual reset

via I/O key

TP Er2 =

Short circuit in pellet

chute sensor

Short circuit = component error Test TR sensor and replace if

necessary + do manual reset

via I/O key

HB Er1 =

Operating panel or cable

connecting operating

panel to main circuit

board broken

Breakage = component error Test operating panel

/connecting cable and replace

if necessary + do manual reset

via I/O key. If display is broken,

error message will remain

active even if a new operating

panel has already been

installed. In this case briefly

press I/O key to permit

recognition of new operating

panel.

RE Er1 =

Bridge at “auxiliary input“

is open

Bridge wire “auxiliary input“ is open or error in

external component/appliance.

Note:

The “auxiliary input“ is for feedback from external accessories. 15

seconds after every start the system checks whether this input is

bridged, i.e. closed, and the preheating programme is only

started if this is the case. The “auxiliary input” is constantly

monitored. Opening of the bridge at the “auxiliary input” results in

an error shutdown / activates the safety function (class 1 error).

Application examples (see also assembly instructions):

1) Flue gas exhaust flap: If a mechanical or motorised exhaust

flap is used, you can connect the make-contact from this flap to

the auxiliary input. The pellet stove will then only start up if the

exhaust flap is open. Any error at the exhaust flap will cause the

appliance to shut down through a safety function. If the motorised

exhaust flap is not completely open within 15 seconds, this will

trigger an error message due to delayed feedback to the

appliance.

2.) Inlet flap for combustion air: function, use and wiring as with

an exhaust flap.

3) Disable function through ventilation system / exhauster hood: If

the ventilation system or exhauster hood has a potential-free

output as operating signal, this output can be connected to the

auxiliary input as a break-contact. In this case the pellet stove will

only go into operation when the exhauster hood / ventilation

system is not in operation.

All the above applications can be connected in series, and the

pellet stove will then only go into operation if all external devices

are working properly and shut down as soon as an error occurs in

any one of them.

Check bridge wire at “auxiliary

input” and mount correctly.

If you are using an external

device, check its wiring and

function (especially make-

contacts) and replace as

necessary.

Then do a manual reset via I/O

key.

Note: To do a reset and

restart after error message

RE Er1, make sure that the

“auxiliary input” has been

bridged again (contact

closed).

Note: If external devices are

connected in series, you have

to check all devices and the

entire external wiring.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Wodtke Frank Airplus S4 Seite 32

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Wodtke Frank Airplus S4

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info