Bedienungsanleitung WOLF-Garten 51 BA (Seite 13 von 38) (Deutsch, Englisch, Holländisch, Französisch, Italienisch)

638534

Zoom out

Zoom in

Vorherige Seite

1/38

Nächste Seite

z Before removing the grass box: Turn off the engine and wait

for the blade to stop. Carefully refit the grass box after empty-

ing.

z Never drive over gravel with the engine running - stones can

be thrown by contact with the blade!

z Where possible, do not mow in wet grass. If the mower ap-

pears to have blocked, turn off the engine, remove the spark

plug lead and wait until the blade comes to a standstill if, for

example:

– to free a blockage in the ejection channel

– to examine or clean the mower

– if a foreign body is encountered. Check whether mower

deck or blade have been damaged. Then correct or repair

the damage before recommencing mowing.

– if the mower strongly vibrates from imbalance (then switch

off immediately and look for the cause).

z NOTE: Danger when grass box equipment is inappropriately

handled.

z If the mower is a self-propelled version then release the drive

clutch bail before you switch on the engine. Do not touch en-

gine or exhaust during or shortly after operation. Hot parts can

lead to burns or provoke frightened movements which may

lead to injuries.

z Turn the engine off if you the leave the lawn mower unatten-

ded and before you refuel.

After working

z The throttle should be closed before switching off the engine.

If the engine is equipped with a petrol shut-off valve then this

be closed after mowing has been completed.

z Do not leave the mower in closed areas after switching off - al-

low it to cool off in the open air before storing away.

z Never keep the machine with petrol in the tank within a buil-

ding in which gasoline vapours may possibly come into con-

tact with naked flames or sparks. Before leaving the mower

remove the spark plug lead and - if fitted - the starting key.

z Lifting and carrying the mower for transport:

z Never attempt to lift the mower with the engine running - nor

with a hot engine - always remove the spark plug lead before

lifting or carrying.

z When folding the mower handlebars, detach starter rope and

make certain that the control cables are not snagged or stret-

ched when folding or unfolding.

z Always carry out the engine oil change with the fuel tank emp-

ty and filler cap fitted. The engine should be warmed up prior

to draining the oil to ensure all sludge deposits are drained

away with the oil.

Maintenance

z Regularly examine all fixing bolts and nuts, particularly those

of the cutter bar, for tightness.

z Maintenance and cleaning of the equipment as well as remo-

ving the protection device may only be performed with the en-

gine stopped and the spark plug lead and - if available - the

starting key, removed.

z Note information on the chassis before cleaning and oil chan-

ge!

z Make certain that all nuts, pins and screws are firmly tightened

and that the unit is in a safe operating condition.

z In order to avoid the risk of fire keep the engine, exhaust, bat-

tery box and the area around the fuel tank free of grass, leaves

or oil.

z If the equipment must be tilted for maintenance work then the

fuel must be completely drained from the tank beforehand.

z Clean the equipment after each use with a hand-brush - not

with water and do not hose down with a high pressure hose in

particular. Make certain to keep the engine cooling fins and

engine cooling air intake clean and free from debris.

z Do not place the equipment in damp areas, near naked flames

or where a spark might ignite petrol vapour.

z If the fuel tank is to be emptied then this should be done out-

doors. Make sure that no fuel is spilled.

z For safety reasons replace worn out or damaged parts.

z NOTE! Always have blades replaced or sharpened by a

WOLF Service Centre, as a blade balance test must be per-

formed in accordance with safety regulations and the blade re-

taining bolt must be tightened to a specified torque.

z Wear suitable work gloves when carrying out the above work,

especially when handling the blade.

Assembly

Fixing of handle

1 ATTENTION! Take care that the switch cable does not

become caught and crused when folding the handle fra-

me.

z Fasten the handle bar as in the illustration

z Set the handle to the desired height .

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

WOLF-Garten 51 BA Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info