Bedienungsanleitung WOLF-Garten Expert 40 E (Seite 14 von 110) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

638175

Zoom out

Zoom in

Vorherige Seite

1/110

Nächste Seite

Mulch

„Mulching“ is a process in which the grass is finely chopped by a

special cutting system and then deposited on the ground. The re-

sult is that the grass does not have to be collected and disposed

of. „Mulching“ also prevents the lawn from drying out.

3 Instructions for mulching

We recommend:

z Depending on the growth of grass, mulch 1 – 2 x per

week

z The grass should not be too high nor too wet!

z Go slow while mulching

z Take care that the blade channels do overlap.

z Do not cut grass more than 20 mm.

3 Note:

Mulching is not advisable in case of moss-affected or

entangled grass, because the cut material stays on the

moss surface and/or entanglement and thus cannot be

absorbed by the ground.

z Regularly scarify and manure the lawn.

Activating the mulch function

1 Attention! Rotary cutter blade

Undertake adjustments on the equipment only after the

motor is switched off and the cutting tool has come to a

standstill.

z Do not start the motor until your feet are at a safe dis-

tance from the cutting tool.

1. Remove the grass collecting bag.

2. Set the switch to „MULCH“.

3. Start the motor.

Maintenance

General

1 Attention! Rotary cutter blade

Before all maintenance and cleaning work:

z pull out the power plug.

z Do not touch running blades.

Cleaning

z Clean mower thoroughly after each mowing with cloth or

brush.

z Clean the mulch flap at regular intervals with a small

broom .

z Do not spray with water.

Winter Storage

z Clean mower thoroughly before storing away.

z Have your mower thoroughly checked once a year by an ap-

proved Service Centre.

z Do not store it in a wet or humid place.

Changing blades

z For all works on blades, coupling and cutter bars, first of all,

pull out the power plug and wear protective gloves.

1 Attention!

An unbalance can develop after regrinding of the blade.

z Always regrind the blades in a specialist workshop,

because an unbalance check should be undertaken

according to the safety regulations.

EXPERT 34 E - EXPERT 37 E

z Always change blades in a specialist workshop. A torque

spanner of 10 mm is mandatorily required.

Fastening torque of the screws: 6 - 7 N-m .

EXPERT 40 E - EXPERT 40 EA

z Always change blades in a specialist workshop. A torque

spanner of 13 mm is mandatorily required.

Fastening torque of the screws: 16 - 18 N-m .

z Use only original WOLF-Garten spare parts.

Adjusting the Bowden cable coupling

1. Raise the drive bracket (1) app. 2 cm and hold.

2. Loosen the locking nut (2).

3. Turn the setscrew (3) left until the drive wheels are blocked

when you pull the mower backwards.

4. Tighten locking nut (2).

Spare parts

Item number Order description Product information

4904 031 Grass catcher (34)

4907 031 Grass catcher (37)

4970 031 Grass catcher (40)

4904 096 Vi 34 FM Replacement blade 34 cm

4907 096 Vi 37 FM Replacement blade 37 cm

4970 096 Vi 40 FM Replacement blade 40 cm

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

WOLF-Garten Expert 40 E Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info