Bedienungsanleitung WOLF-Garten Power Edition 46 B (Seite 13 von 42) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Türkisch)

638677

Zoom out

Zoom in

Vorherige Seite

1/42

Nächste Seite

Emptying of Grassbox

When the collection bag is full, the flap lowers by itself.

1 Attention! Rotary cutter blade

Undertake adjustments on the equipment only after the

motor is switched off and the cutting tool has come to a

standstill.

z Empty collection bag.

z Remove potential blockages in the cutting space before

starting.

3 Instructions for level indicator:

For an efficient functioning of the level indicator, regularly

clean the holes under the level indicator in the collection

bag with a hand brush.

Tips for mowing

z To prevent strips of grass from being left unmowed, the cutting

paths must always overlap a few centimeters .

Maintenance

General

1 Caution! Rotating blades

Before all maintenance and cleaning tasks:

z Remove the sparking plug lead.

z Take care not to grab running cutters.

z For safety reasons, replace any worn or damaged parts.

When replacing, follow the instructions for installation

z Check all the visible fastening bolts and nuts regularly to be

sure they are snug and tighten them.

z Only use spare parts made by WOLF-Garten; otherwise you

do not have a guarantee that your mower meets safety regu-

lations.

Cleaning operations and blade change

1. Pull off the sparkplug connector!

2. Raise the cutting height to its highest position .

3. For cleaning and changing the blade, tip the mower to the side

as illustrated .

Sharpening and changing blade

1 Caution! Rotating blades

Before all maintenance and cleaning tasks:

z Remove the sparking plug lead.

z Take care not to grab running cutters.

z Change of blades only be carried out by an approved service

station.

z Gloves should be worn at all times when working on the blade.

Remove ignition key and spark plug lead when working on the

blade.

z Damaged blades should always be replaced in pairs to ensure

even balance.

3 Information for Service Centre, blade retaining screw to

be tightened to:

A/F 17 mm = 38-42 Nm / A/F 13 mm = 16-20 Nm

Adjusting the Bowden cable coupling

1. Raise the drive bracket (3) app. 2 cm and hold.

2. Loosen the locking nut (1).

3. Turn the setscrew (2) left until the drive wheels are blo-

cked when you pull the mower backwards.

4. Tighten locking nut (1).

Change oil only

z While engine is warm and fuel tank empty.

z Change oil after the first 5 working hours. There after change

engine oil every 25 working hours and at the end of the mo-

wing season. Change engine oil more frequently if working un-

der extreme and dusty conditions.

1. Remove oil filler cap.

2. Tilt machine slowly to side and allow oil to drain from the

crankcase through the filler .

3. Oil Fill .

Cleaning of Spark Plug

z Check and clean regularly

z Reset plug gap as required (0,76 mm).

Cleaning of air filter

Refer to the engine manufacturer‘s handbook supplied.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

WOLF-Garten Power Edition 46 B Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info