Bedienungsanleitung WOLF-Garten TC 32 ME (Seite 9 von 24) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

638400

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

1. General

• The machine must not be used by youths under the age of 16

or by persons who are not familiar with the operating instruc-

tions.

• The machine must not be used in the presence of human

beings, especially children, or animals.

2. Preparation

• Always wear shoes and long pants when operating the

machine. Never operate the machine when barefoot or when

wearing open sandals.

• First examine the lawn for foreign objects that could be thrown

by the machine and remove them.

• Check to make sure the machine and the cutting unit are in

proper working order.

3. Cable

•

Please work with safety cables from WOLF. For the connection

only lines which are not lighter than rubber hose lines H0 7

RN-F to DIN with a minimum diameter of 3 x 1,5 mm

must

be used.

•

They must be waterproofmobile decvices that are used outdoors

must be connected via a residual current circuit breaker.

• Use a leakage-protective system (RCD) with a leakage cur-

rent of no more than 30 mA.

• Attach connection cable to traction relief. Make sure that in

does not rub against edges, pointed or sharp objects. Do not

squeeze cable through door or window gaps.

• Switching devices must not be removed or bridged (e.g. tying

of switching lever to guide spar).

4. Operation/maintenance

• Operate the machine only in daylight or sufficient artificial

light.

• The machine must never be used when it is raining. If pos-

sible, avoid using the machine when the grass is wet. The

machine must never be washed or rinsed with water.

• Make sure that you have a firm hold, especially on slopes.

Never run, but walk forwards slowly.

• Always mow slopes back and forth, never up and down.

• Special care is required when changing directions or when

you pull the machine toward yourself.

• Never use a machine with a damaged housing or missing

protective guards.

• Before you leave or transport the machine or perform inspec-

tion, cleaning or other maintenance, you must:

- shut off the motor

- wait until the blades stop turning

- pull the power plug

• When adjusting, avoid inserting hands or feet between the

blades and the fixed parts of the machine.

•

Keep hands and feet away from the revolving blades.

•

If the blade spindle becomes blocked, switch off the motor

and pull the power plug. Remove any objects and check for

damage. Any damage must be repaired before the machine

can be operated again.

• Before using the extension cord, check it for damage and

wear. Replace the cord if necessary. Do not use the machine

if the cord is damaged.

• The extension cord must be free. Lay the cord so that the

machine cannot run over it. The extension cord must remain

away from the blade spindle.

• These units have been performance tested according to

VDE guidelines for intermittent service S 6 with a duty cycle

of 40%. This corresponds to normal mowing operations with

alternating load and idle cycles.

Safety instructions

Operation

Operating times

Please check noise abatement regulations prevailing in your

country.

Adjust cutting height (g. B1)

Only if the motor is switched off and cutting tool is at a

standstill.

There are 5 positions for cutting height (18, 23, 28, 32,

40 mm).

Pull the adjusting arm (1) away from the sidepiece and let it

re-engage in the desired cutting height position (2). Adjust, by

1 position only, alternating right and left. The adjustment arms

must always be on the same height position.

Note: Adjust the cutting height so that the bottom blade has

no ground contact if there are uneven areas on the lawn

surface.

Selection of Cutting height

If possible, mow when grass is dry in order to protect turf. Do

not se cutting position too low when mowing very hight or wet

grass. We recommend an average cutting height of 28 mm.

To maintain a well-groomed lawn, the grass must be cut at

least once a week. The grass must be dry, for the most part,

when it is mowed. The mowing path should be as straight as

possible using a normal walking speed. The mowing paths

must always overlap by several centimetres to prevent strips

of grass being left uncut.

Insert connection cable in the strain relief (fig. B2)

Connecting to the mains (230 Volts, A.C., 50 Hz)

The mower operates from any normal household mains

supply, provided with a 10 Amp. fuse.

Note: Use a residual current device (RCD) rated for a

residual current not greater than 30 mA.

Starting

Switch on motor with mower placed on level and firm ground,

not in high grass - alternatively tilt slightly.

Note

Switch on mower only for mowing. Never allow motor to run

at idle longer than one minute!

Switch-on motor (fig. B3)

1. Depress button and hold (1).

2. Lift up bar and release button (2).

Switch-off motor (fig. B3)

Release bar (2).

Mowing

Always let cable trail on the cut side of the lawn.

Cable guidance: Place the cable firmly off the lawn or on the

already cur side of the lawn when starting to mow.

New blade condition „Mach 15“

Mowing:The blade is automatically optimized, i.e. the blade

spindle adapts exactly to the bottom blade after mowing for

some time (approx. 2 hrs.).

Turning

The mower should be turned on a surface of the lawn that

has already been mowed.

Safety switch

In case of overload or blocking, the motor shuts down

automatically!

Pull power plug and eliminate the cause of the problem!

Overload:

Cutting height is too low, or forward speed is too fast

Blocking:

Foreign object in cutting area (e.g. branches).

The machine can be switched on again after about 5 min.

WOLF-Garten TC 32 ME Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info