Bedienungsanleitung WOLF-Garten VS 302 E (Seite 12 von 86) (Alle Sprachen)

799044

Zoom out

Zoom in

Vorherige Seite

1/86

Nächste Seite

12 G

Operation

Operating times

Please check noise abatement regulations prevailing in your

country.

Feed cable through the strain relief

Please feed cable through the strain relief.

Connecting to the mains (230 Volts, A.C., 50 Hz)

The machine operates from any normal household mains sup-

ply.

3Note: Residual current protection device

These protection devices safeguard while touching

damaged wires, from insulation flaws and in certain cases,

also while damaging live wires.

We recommend that the equipment only be plugged into

a power socket, which is protected by a residual current

protection device (RCD) with a residual current of not

more than 30 mA.

Adjust operating depth

1Caution! Only with motor switched off and non-mowing

scarifying / aerating roller.

1Caution! The working depth must be set correctly befo-

re the unit is used for the first time. The hight adjust-

ment lever may be moved to the first working depth

setting only (position „1“)

3Note

If the blades/aerator tines are worn, the working depth must

be readjusted subsequently. An optimum working depth is

obtained when the blades/aerator tines of the cutter are in-

serted 2–3 mm into the ground.

If the working depth is too great, the unit may be overloaded

and cause damage. Therefore, ensure that the working

depth is set correctly.

Increasing the working depth (cutters towards the

ground) (a, b)

–Set height adjustment lever (depending on model) accor-

ding to wear.

–Settings pos. „2, 3, 4“ are not required until the blades/aera-

tor tines are worn. Depending on the degree of wear, gradu-

ally set the blades lower, starting at pos. „2“.

Reducing the working depth (a, c)

3Scarifying / aerating test:

Set height adjustment lever in working position „1, 2, 3,

4“ .

Start tool

On hearing stones being hit or blocking of the motor im-

mediately switch off tool

Reducing the working depth : Set height adjust-

ment lever in working position „1, 2, 3, 4“.

Start scarifying / aerating test again

When used regularly the working depth may be adjusted ac-

cording to the wear of the blade (+).

Recommended working heights

well kept lawns with stone-free, soft ground

–Set tool exactly to ground height

stony, untidy lawns

–Set tool to ground height

–Increase working height if stones are thrown up

unkempt, extremely mossy lawns

–Start with a high working height

–Do not overload appliance (reduce working height if motor

blocks)

–Cut vertically and crossways several times

Scarifying / aerating

1. Depress button (1) and hold.

2. Lift up bar (2) and release button (1).

3. Switch-off motor: Release bar (2).

1Important:

Place the cable firmly off the lawn or on the already cut side

of the lawn when starting to mow.

Maintenance

General

1Attention! Rotary cutter blade

Before all maintenance and cleaning work:

 pull out the power plug.

 Do not touch running blades.

Cleaning

Clean the unit thoroughly with a brush after each use.

Do not spray with water.

Store unit in a dry room.

3We recommend

Allow a WOLF-Garten-service centre to check the unit in the

autumn.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

WOLF-Garten VS 302 E Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info