Bedienungsanleitung Worcester-Bosch Greenstar Comfort I RF - 2014-2022 (Seite 7 von 24) (Englisch)

809346

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

Installation

Comfort I– 6720810964 (2014/07)

Fig. 3 Suggested Programmer wall plate mounting

▶ Engage the four clips on the back of the Programmer [2]

with the four slots on the wall plate as shown in figure 4

▶ Push the Programmer down into the wall plate to secure

▶ Engage the tabs on the top retainer [3] into the slots on the

wall plate [1] and push down onto the Programmer

Fig. 4 Fitting Timer to wall plate assembly

3.3 Time and date set up

▶Turn the boiler ON

▶ Fit the batteries into the Room thermostat, refer to

section 9.1 for instruction on how to fit the batteries

Before mounting the Room thermostat on the wall, it is good

practice to find a position that affords good signal strength.

To check the signal strength, refer to section 6.7 S2 RF Signal

strength on page 18.

The unit will initially display an error code A21 “No wireless

signal to EMS interface”, refer to chapter 7 for information on

fault codes.

When they have established RF communications with each

other, the Programmer/Receiver display will revert to a factory

default time and date with the control in “Auto” mode for both

heating and hot water.

The Room thermostat will display the current room

temperature.

3.4 Pairing/Unpairing the units

3.4.1 Programmer/Receiver - Installer menu -

Radio settings - Pair

The Room thermostat and Programmer/Receiver must be in

the same mode of pairing.

The Programmer/Receiver Pairing/Unpairing function is found

under the Installer menu, in Radio settings and Pair.

To enter the Installer menu, press the menu button and return

button for more than three seconds.

Six icons are shown across the top of the display:

1. Heating

2. Hot water

3. Holiday

4. Info

5. Settings

6. Installer setting

Turn the knob to select the Installer icon and press the

knob to enter the function.

The Programmer/Receiver and Room

Thermostat are factory set and “Paired” to

each other, so that they are fully operational.

6720810964-24.1Wo

6720810964-25.1Wo

Set the current time and date

▶ Hold the menu button down for more than

3 seconds to enter the user menu, turn the

knob to select Settings and press to enter

▶ Refer to section 5.1.5 Info - Time/Date

for setting the Time and Date, and clock

format

The Programmer/Receiver and Room

thermostat are delivered together and are

factory paired, they automatically connect

when the system is switched on. There is no

need to pair/unpair the units during

installation, unless there is a problem with

one or both of the units.

If a faulty unit is replaced with a new unit, then

the existing unit must be unpaired before the

two units can be paired.

If the units have to be paired/unpaired, all units

must be in the same pairing/unpairing mode.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Worcester-Bosch Greenstar Comfort I RF - 2014-2022 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info