Bedienungsanleitung Worcester-Bosch Greenstar Danesmoor Utility Regular - Utility System (Seite 40 von 64) (Englisch)

809256

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

Commissioning

Greenstar Danesmoor Utility 2022+ and Utility System 2022+ - 6 721 846 263 (2022/01)40

6 Commissioning

6.1 Pre-Commissioning checks - 18/25 Regular shown

1. Check that the service and water pipes are connected correctly.

▶ Check that all unused sockets are capped.

2. Check that the oil supply is Kerosene (Class C2) and that the

pipework is connected correctly to the oil pump via the supplied

flexible oil hose.

▶ Check that the burner is seated correctly on its mounting flange and

that the oil hose/s are routed correctly.

See page 51, figure 90 for correct routing of the oil hose.

▶ Turn on the main oil supply valve at the tank, check the oil supply

pipework and connections. Rectify any leaks.

3. Check the flue is correctly fitted and the connections are secure.

4. Check the condensate pipework is correctly fitted and connected.

▶ Check the condensate trap is filled with water.

Fig. 60 Pre-Commissioning checks

6.2 Filling the system

▶ Open all system and radiator valves.

▶ Turn on the water main stop cock.

▶ Open vented systems only:

– Turn on the water to the system feed and expansion cistern and

allow the system to fill.

▶ Sealed systems only:

– Check and if required, adjust the expansion vessel pressure using

the Schraeder type valve.

▶ Fill the system to between 1 and 2 bar pressure via a WRAS approved

filling link.

▶ Vent all radiators, retighten when completed.

▶ Monitor the pressure gauge during venting and repressurise if

required.

▶ Check the system and correct any leaks.

▶ Bleed air from at least one of the secondary heat exchanger air vents

(a radiator key is ideal for this). There are two venting bosses [1] on

the top of the secondary heat exchanger. Only one can used if fluing

to the side.

Fig. 61 Manual vent points

[1] Manual vent points (each side of the secondary heat exchanger).

CAUTION: 230 Volts

▶ Isolate the mains electrical supply before starting any

work and observe all relevant safety precautions.

NOTICE: If the boiler is not to be commissioned then:

▶ After successfully completing all of the checks and any

rectification work, close the water valves, shut off the

oil supply and electrically isolate the boiler.

▶ Complete the installation part of the Guarantee

Registration Card, and complete a CD10 or equivalent

to inform the LABC of the installation.

▶ Refit the top panel.

1. 3.

System boiler only

The charge pressure of the built-in 10 litre expansion

vessel is 0.5 bar as supplied, which is equivalent to a

static head of 5 metres. At 1 bar pressure the vessel will

provide 92 litres expansion capacity, the boiler has a

primary water capacity of 20 to 22 litres and therefore

additional system expansion capacity may be required.

▶ If an extra expansion vessel is fitted to the central

heating return, adjust this to the same pressure as

the appliance internal expansion vessel, refer to

separate instructions supplied with the extra

expansion vessel.

6720813284-21.1Wo

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Worcester-Bosch Greenstar Danesmoor Utility Regular - Utility System Seite 40

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info