809350
42
Zoom out
Zoom in
Vorherige Seite
1/48
Nächste Seite
42
Eliminate fault
Sense ll – 6 720 812 775 (2014/10)
Faults you can fix yourself
If an operating fault cannot be rectified:
Contact an authorised installer, or customer service.
Submit error code, additional code and control unit ID
number.
Fault
code
Sub-
code
Cause or fault
description Test procedure/Cause Corrective measure
Nothing appears on the display System is switched off. Switch on the system.
The power supply to the controller has been
interrupted.
Check that the controller is
correctly seated in its wall
bracket.
A01 810 DHW stays cold. Check if water is possibly being drawn from the
DHW cylinder constantly due to taps being open.
If water is being drawn
constantly, take action to stop
this.
A01 811 DHW heating: thermal
disinfection failed
Check if water is possibly being drawn from the
DHW cylinder constantly due to taps being open.
Take action to stop water being
drawn constantly.
A11 1010 No communication via
BUS connection EMS 2
Check that the controller is
correctly seated in its wall
bracket.
A11 1038 Invalid time/date Date/time not yet set Set date/time.
Prolonged loss of power supply Avoid voltage failures.
A11 3061
...
3064
No communication with
heating circuit module
(3061: heating
circuit 1, ..., 3064:
heating circuit 4)
Check that the controller is
correctly seated in its wall
bracket.
A11 6004 No communication w.
solar module
Check that the controller is
correctly seated in its wall
bracket.
A21
...
A24
1001 No BUS connection between Sense ll and Sense I
in the corresponding heating circuit (A21:
heating circuit 1, ..., A24: heating circuit 4).
Check that the controller is
correctly seated in its wall
bracket.
A41
A42
4051
4052
Thermal disinfection
failed.
Check if water is possibly being drawn from the
DHW cylinder constantly due to taps being open.
Take action to stop water being
drawn constantly.
H... Maintenance required. The system keeps
operating as far as possible.
Make arrangements to have the
system serviced by your
Servicing Engineer.
H07 1017 Water pressure in the system is too low. This
value is only displayed if your system is equipped
with a digital pressure sensor.
Top up the heating water as
described in the operating
instructions of the heat source.
Table 40
__ _
Table 41 The control unit ID number must be filled in here by the installer at installation.
42

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Worcester-Bosch Greenstar Sense ll wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info