Bedienungsanleitung Worcester Greenstore Ground Source (Seite 11 von 28) (Englisch)

809329

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

SETTINGS

6 720 802 172 (2012/06) 11

12.4 OPERATING MODES

•With electric additional heat; the electric additional heat is

permitted to work at the same time as the heat pump to meet the

demand, when the heat pump cannot meet it by itself. Alarm mode,

Extra hot water and Hot water peak also activate the additional heat.

•With mixed additional heat (option); mixed additional heat which is

permitted to work at the same time as heat pump. The additional heat

is also used during alarm operation.

A hot water electric heater is required for production of extra hot

water and hot water peak. In this case, the electric additional heat in

the heat pump is disabled.

13 SETTINGS

13.1 MODE BUTTON FUNCTIONS

By pressing , the following functions can be used directly:

•Room temperature normal / Temperature increase/decrease

•Party

•Holiday

•Extra hot water duration

> Room temperature normal / Temperature increase/decrease

Here, temperature changes for Circuit 1 can be made. If this circuit is

equipped with a room temperature sensor, the display shows Room

temperature normal, otherwise Temperature increase/decrease is

shown.

▶ Use this function to simply increase or decrease the heat when there

are no room controllers.

– – gives approx. 1 °C lower room temperature.

– gives approx. 0.5 °C lower room temperature.

+ gives approx. 0.5 °C higher room temperature.

++ gives approx. 1 °C higher room temperature.

> Party

Party mode means that a running room program is stopped during the

set time in order to avoid a temperature drop.

>> Number of hours

▶ Select the number of hours that party mode should be active for.

The function starts immediately on all activated circuits.

>> Circuit 1

>> Circuit x

▶Select Yes to enable party mode.

Party mode can be enabled for each installed circuit. The menu is

displayed only if more than one circuit is installed.

>> Deactivate party mode

▶Select Yes to disable party mode on all activated circuits.

The heat pump returns to program mode.

The menu is displayed only if party mode is active.

> Holiday

The same functions are included here as in the Holiday

menu ( Chapter 13.4).

> Extra hot water duration

▶ For a description of setting Extra hot water

(Chapter 13.3).

13.2 ROOM TEMPERATURE

Press the button in the standard display to open the main menu.

Select Room temperature to adjust the heating.

The following options are available under Room temperature:

•Circuit 1 Heating

•Circuit 2, 3...

•General

> Circuit 1 Heating

>> Heat curve

The heat curve constitutes the basis for the control unit's control of the

temperature on the heating water to the circuit and indicates how high it

needs to be in relation to the outdoor temperature. The control unit

increases the temperature of the heating water when the outdoor

temperature drops. The temperature of the heating water out to the

circuit, i.e. the flow temperature is measured by sensor T1 for circuit 1

(full name E11.T1) and sensor T1 for circuit 2 (full name E12.T1).

The Multi module accessory is required for mixed

additional heat and hot water electric heater.

The button can be used to change the language of

the control unit.

▶ Hold down the button for at least five seconds

in the initial menu and then select language.

Factory setting 20.0 °C

Lowest value 10.0 °C

Highest value 35.0 °C

Table 4 Room temperature, normal

Factory setting =

Alternative – – , – , =, +, ++

Table 5 Room temperature increase/decrease

It always takes some time for a change of a heating

setting, e.g. an increase or decrease in room

temperature, to apply. The same applies in the event of a

quick change of the outdoor temperature. This is why

you should always wait for at least 24 hours before

making a new change.

Factory setting 0h

Lowest value 0h

Highest value 99h

Table 6 Party duration

Factory setting No

Alternative No/Yes

Table 7 Enable party mode

Factory setting No

Alternative No/Yes

Table 8 Deactivate party mode

Factory setting 0h

Lowest value 0h

Highest value 48h

Table 9 Extra hot water duration

After a period with blocked hot water production, e.g.,

holiday, it is recommended to enable the extra hot water

function so as to eliminate bacteria and quickly reach the

correct hot water temperature.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Worcester Greenstore Ground Source Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info