809329
13
Zoom out
Zoom in
Vorherige Seite
1/28
Nächste Seite
SETTINGS
6 720 802 172 (2012/06) 13
Fig. 27
Turn the menu dial to change the value.
Fig. 28
Press the dial to save or use to return without saving.
Use to leave the curve setting window and return to the menu.
>> Compressor x operating time on/off
Select how long the compressor should be on or off in heating mode.
Higher set values result in fewer compressor starts and stops, which
achieves higher economy. However, more pronounced temperature
fluctuations in the heating system may result than with lower values.
>> Room temperature program
Choose if the circuit should be controlled with a program or not.
HP optimized
This means that the control unit is only controlled by the flow set point
value ( Chapter 13.2.1), without programmed changes during the
day. Optimised operation provides the best comfort and energy savings
in the vast majority of cases.
Program 1 and 2
These selections provide an opportunity to define user programs for
time control by adjusting the start and stop times, as well as a normal and
an programmed temperature.
To set the desired time of day:
▶Select Program 1 or Program 2.
Go to menu View/edit active program.
Select day by turning the menu dial.
Fig. 29
Press the menu dial to mark the value to be changed.
Fig. 30
Turn the menu dial until the desired setting has been selected.
Then press the menu dial.
Turn the menu dial to be able to set additional values in the same way
as above.
Go back one step with .
▶Select Saving alternative:
Return without saving
Program 1
Program 2
The set changes are saved as a selected program or not at all.
To adjust the normal temperature, proceed to menu Room
temperature normal.
To adjust the exceptional temperature, proceed to menu Room
temperature exception.
Room temperature program when there is a room controller:
>> Room temperature program
>>> Active program
If a program is selected, the following (if the menu button is turned) is
displayed:
>>> View/edit active program
>>> Room temperature normal
Set the desired set point for the room temperature.
Recommendations:
Increase the value of the right point if it feels too cold
at low outdoor temperatures.
Increase the value of curve at 0 °C if it feels a little cold
at outdoor temperatures around 0.
Increase or decrease the value of the curve equally at
the right and left points to fine adjust the heat (the
curve is offset parallel).
Factory setting 20.0
Lowest value 10.0 (Comfort)
Highest value 30.0 (Economy)
Table 10 Compressor operating time on/off
Factory setting HP optimized
Alternative HP optimized
Program 1
Program 2
Table 11 Program selection, circuit 1
6 720 614 789-21.3I
6 720 614 789-22.3I
Program Day Start Stop
Program 1, 2 Mon - Sun 5:30 22:00
Table 12 Program 1 and 2
Factory setting 20.0 °C
Lowest value 10.0 °C
Highest value 35.0 °C
Table 13 Room temperature, normal
6 720 643 415-13.1I
6 720 643 415-14.1I
13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Worcester Greenstore Ground Source wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info